Dionex ICS-900 Скачать руководство пользователя страница 115

Страница: 115 / 142

C • TTL and Relay Control

Doc. 065215-02 9/09

107

4. Select the Relay output name (

Pump_ECD_Relay_1

Pump_ECD_Relay_2

) and press the

key to open the Device

Configuration dialog box (see

Figure C-6

NOTE Select Pump_ECD_Relay_2 if an AS40 is already

connected to Pump_ECD_Relay_1.

5. Select the

Flow

Zero

check box and click

The ICS-900 will now open this relay output when the pump flow stops and
close the relay when the flow starts.

The relay can then be used turn a

connected accessory device off and on with the pump flow.

To use this relay output for another function, clear the check box. Chromeleon
or Chromeleon Xpress will then control the relay output (see

Section C-4

Figure C-6. ICS-900 Server Configuration Properties: Flow Zero Configuration

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды