Dionex ICS-3000 Скачать руководство пользователя страница 57

Страница: 57 / 392

Doc. 065031-04 1/08

DC Description

2.11 DC Front Features

A status bar on the front of the ICS-3000 Detector/Chromatography Module (DC)
(see

Figure 2-12

) includes buttons for controlling certain DC functions, as well as

LEDs that indicate the status of several DC components and functions.

Figure 2-11. DC Status Bar

Button/LED Label

If the LED Is On

If the LED Is Flashing

CONNECTED

The DC is connected to a
Chromeleon or Chromeleon Xpress
timebase.

Does not flash.

ALARM

The leak sensor is wet or there was a
valve or suppressor error. Check the
Chromeleon or Chromeleon Xpress
Audit Trail for the cause.

Does not flash.

SUPPRESSOR 1
SUPPRESSOR 2

The suppressor is on and current is
being applied.

Does not flash.

OVEN UPPER

The upper compartment is at its set
temperature.

The upper compartment is
transitioning to the set
temperature. The
compartment is not ready for
operation.

OVEN LOWER

The lower compartment is at its set
temperature.

The lower compartment is
transitioning to the set
temperature. The
compartment is not ready for
operation.

CONNECTED

ALARM

SUPPRESSOR

OVEN

VALVE 1

VALVE 2

UPPER

LOWER

LOAD

INJECT

LOAD

INJECT

Содержание ICS-3000









































































































































































































































































































































































































Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды

Dionex ICS-3000, Руководство оператора

Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды