Dionex ICS-3000 Скачать руководство пользователя страница 306

Страница: 306 / 392

ICS-3000 Ion Chromatography System

290

Doc. 065031-04 1/08

7. Turn the EluGen cartridge right-side up, and check for bubbles in the

eluent generation chamber. If necessary, shake and tap the cartridge to
remove bubbles.

8. Reinstall the EluGen cartridge in the holder. Remove the 10-32 plug

from the vent opening and reinstall the luer adapter and vent line.

9. Push the cartridge’s electrical cable connector onto the

EGC 1

(or

EGC

) bulkhead connector. Twist the ring on the cable connector

fingertight to secure it.

9.13 Replacing the CR-TC

Replace the CR-TC when the background and drift are not acceptable.

The CR-TC replacement procedure consists of:

•

Removing the old CR-TC (see

Section 9.12.2

)

•

Installing and hydrating the new CR-TC (see

Section 9.13.2

)

•

Completing the plumbing for the new CR-TC (see

Section 9.13.3

)

Refer to

Figure 9-12

for a flow schematic of the EG and CR-TC.

9.13.1 Removing the Old CR-TC

1. On the

Pump

tab page on the panel tabset, click the

Motor

switch to

turn off the pump flow. This turns off the power to the EluGen
cartridge and the suppressor, also.

2. Open the front door of the EG.

3. Push down on the slide release latch and pull the tray forward until it

reaches the stop.

4. Follow the instructions in

through

disconnect the EluGen cartridge electrical cable from the bulkhead
connector, cap the EluGen cartridge vent opening, remove the
EluGen cartridge, and disconnect the inlet and outlet tubing.

5. Pull the CR-TC off the ball studs on the component mounting panel.

6. Disconnect the liquid lines from the four ports on the CR-TC.

Содержание ICS-3000









































































































































































































































































































































































































Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды

Dionex ICS-3000, Руководство оператора

Результаты поиска

Содержание ICS-3000

Отзывы:

Похожие инструкции для ICS-3000

Бренды по названию

Популярные бренды