Dionex ICS-3000 Скачать руководство пользователя страница 278 | Manualshive

Страница: 278 / 392

background image

ICS-3000 Ion Chromatography System

262

Doc. 065031-04 1/08

NOTE After starting the pump, wait at least 5 minutes

(longer for flow rates below 1.0 mL/min) before
beginning an analysis. This allows the DP/SP
Moduleware to stabilize the flow rate.

9.4

Replacing the Check Valves

A dirty check valve causes erratic flow rates and pressures; in addition, it may
cause the pump to lose prime and/or be difficult to reprime. If a check valve leaks
or is dirty, it should be replaced.

1. Click

Motor

on the pump Control panel in Chromeleon or Chromeleon

Xpress to turn off the pump flow.

2. Begin monitoring the

Current Pressure

reading on the Control panel. When

the system pressure reaches zero, do the following:

•

Disconnect the pump from the software by clearing the

Connected

check

box on the Control panel.

•

Press the

POWER

button on the front of the DP/SP for 2 seconds to turn

off the pump.

3. Open the DP/SP door to access the mechanical components.

4. Use the handles on the component mounting panel to pull the panel forward

until it reaches the stop.

NOTE On newer pumps, three red Phillips screws are installed

on the component mounting panel before shipment from
the factory. If the mounting panel does not move freely,
make sure these screws have been removed.

5. To prevent contamination of pump parts, wear cleanroom gloves while

disassembling the pump head.

Never disassemble the pump head with bare hands. Even minute
particles of dust, dirt, etc., on the check valves or piston can
contaminate the inside of the pump head and result in poor pump
performance.

«
...
276
277
278
279
280
...
»

Содержание ICS-3000









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-3000

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Rapid Technic Страницы: 152

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: Tanco Страницы: 112

Smart Plus PHT-35LHS

Бренд: Vatech Страницы: 190

Бренд: Yetter Страницы: 24

Бренд: Yetter Страницы: 32

Бренд: Feniex Страницы: 5

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

Бренд: ALLSPEEDS Страницы: 22

Бренд: Vibration Research Страницы: 40

Бренд: Eco Stage Страницы: 17

Бренд: Ace Страницы: 37

Бренд: Next Sight Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды