Dionex ICS-3000 Скачать руководство пользователя страница 221 | Manualshive

Страница: 221 / 392

background image

8 • EG Troubleshooting

Doc. 065031-04 1/08

205

This error occurs if the flow rate is set to a value the EG does not support. The
DP/SP flow rate range is 0.001 to 10.0 mL/min; however, when an EG is
installed, the allowed range is 0.01 to 3.00 mL/min. The recommended
operating range is 0.4 to 2.00 mL/min.

To troubleshoot:

Set the flow rate to a value within the allowed range.

This error occurs if the selected concentration is too high for the current flow
rate.

To troubleshoot:

Set the flow rate to a value within the allowed range. The allowable eluent
concentration for a particular application depends on several factors: the flow
rate, suppressor type, EluGen cartridge type, and cartridge configuration. For
details, refer to

This error occurs when the current applied to the EluGen cartridge exceeds
the maximum current allowed. (The EluGen current is automatically turned
off to prevent damage to the cartridge.) This error may also occur if the liquid
flow to the cartridge is interrupted.

EG1 invalid flow.

-or-

EG2 invalid flow.

EG1 invalid flow rate-concentration.

-or-

EG2 invalid flow rate-concentration.

EG1 over current.

-or-

EG2 over current.

«
...
219
220
221
222
223
...
»

Содержание ICS-3000









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ICS-3000

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: YardShape Страницы: 50

Бренд: Eagle Страницы: 3

Бренд: Haigh Страницы: 60

Бренд: Handler Страницы: 25

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: EuroLite Страницы: 28

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Garden Treasures Страницы: 2

Бренд: Agilent Technologies Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды