DINSEO DIX TIG GO 1906.M HF, Руководство по эксплуатации

Страница: 19 / 26

19
Spot welding with DIX ARC COOL SPOT
function with TIG HF DC welding
Innovative TIG HF DC tack weld device that makes it possible
to do precise, safe tack welding with very little heat applied. Thanks
to the “Perfect-Point” mode, DIX ARC COOL SPOT guarantees
perfect centring of the welding point. The “Perfect-Point” mode is
activated by touching the workpiece to be welded with the tung-
sten tip, at the exact point at which you wish to do the tack weld.
Proceed as follows:
1) Start the welding power source by turning the power supply
switch to position I .
2) Push the SELECT WELDING PROCESS (T5) key and select
the TIG DC process, with HF ignition.
3) Press the WELDING MODE SELECTION Key (T6)
and go to one of the SPOT WELDING DIX ARC
COOL SPOT function. The TACK WELD and
LEDs are lit continuously.
4) Press and release the WELDING PARAMETERS
SELECTION Key (T7) until the SPOT WELD LED
starts flashing.
5) Rotate the ENCODER knob (E) to set the SPOT
WELDING time required (0,01÷10,0 sec).
6) By pushing the WELDING PARAMETERS SELECTION (T7)
key a number of times it is possible to set the various TIG
WELDING PARAMETERS (see the “TIG Welding” paragraph
- WELDING PARAMETERS).
7) Hold the SELECT WELDING PARAMETERS (T7) key down
to save the parameters chosen.
8) Once the all the selections/regulations indicated above
have been made, welding can begin. Ignite the arc using
“distance”ignition or by touching the workpiece to be welded
with the tungsten tip. In the latter case, the “Perfect-Point”
mode is activated.
9) During the welding process the DISPLAY shows the real Amps
(A) at which the operator is actually welding.
T5
Multi spot welding with Multi-DIX ARC
COOL SPOT function with TIG HF DC
welding
The Multi-DIX ARC COOL SPOT function can be used for cold
tacking in quick succession, to further extend the benefits of an
individual DIX ARC COOL SPOT point. Thanks to the “Perfect-
Point” mode, DIX ARC COOL SPOT guarantees perfect centring of
the welding point. The “Perfect-Point” mode is activated by touch-
ing the workpiece to be welded with the tungsten tip, at the exact
point at which you wish to do the tack weld. Proceed as follows:
1) Start the welding power source by turning the power supply
switch to position I .
2) Push the SELECT WELDING PROCESS (T5) key and select
the TIG DC process, with HF ignition.
3) Press the WELDING MODE SELECTION Key (T6)
and go to one of the SPOT WELDING Multi-DIX
ARC COOL SPOT function. The TACK WELD LED
flashes, whereas the LED is lit continuously.
4) Push and release the SELECT WELDING PARAM-
ETERS (T7) key to be able to set the 2 parameters
by rotating the ENCODER Knob (E):
•
Total tack welding time “t...” for the sequence of
individual DIX ARC COOL SPOT points (0,01-
10,0 sec).
•
Individual DIX ARC COOL SPOT point “P...” time
(0,01-1,0 sec).
5) By pushing the WELDING PARAMETERS SELECTION (T7)
key a number of times it is possible to set the various TIG
WELDING PARAMETERS (see the “TIG Welding” paragraph
- WELDING PARAMETERS).
6) Hold the SELECT WELDING PARAMETERS (T7) key down
to save the parameters chosen.
7) Once the all the selections/regulations indicated above
have been made, welding can begin. Ignite the arc using
“distance”ignition or by touching the workpiece to be welded
with the tungsten tip. In the latter case, the “Perfect-Point”
mode is activated.
8) During the welding process the DISPLAY shows the real Amps
(A) at which the operator is actually welding.
T5