DINSEO DIX TIG GO 1806.M AC/DC, Руководство по эксплуатации, Страница: 23 / 30

23
TIG “AC and DC” welding
- Welding parameters
•
The Welding power source can be configured in the follow-
ing 2 ways:
•
STANDARD (Std) configuration.
•
SPECIAL (SPE) configuration.
STANDARD CONFIGURATION (Std)
When it leaves the factory the welding power source is normally
configured in STANDARD (Std) mode.
To check the configuration, carry out the following operations:
1) When the welding power source is off, push and hold the
“PRG” PROGRAM key down (T2).
2) Start the welding power source by turning the power supply
switch to position I .
3) The DISPLAY (D) shows the following message: Std (welder
configured in STANDARD mode).
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T
b
f
T
p
I
1 I
p
I
b
PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
PULSE
SYN
FAST
SLOW
WAVE
T2
D
4) Press the “PRG” PROGRAM key (T2) to confirm.
The WELDING PARAMETERS included, programmable, and that
can be edited (by turning the ENCODER key) in a STANDARD
(Std) configuration can be broken down into 3 different sub-groups:
1 - “BASIC” WELDING PARAMETERS
Press the WELDING PARAMETERS SELECTION Key (T10) a
number of times to set:
L18 L11 L22
L17 L16 L13 L12
T10
L12 PRE-GAS duration (0,05 ÷ 1,00 sec)
WARNING: This CANNOT be programmed when the TIG DC with
“Lift” type ignition welding processes is active.
L18 INITIAL welding CURRENT
1806.M AC/DC 2506.M AC/DC
TIG DC 5 ÷ 220 A 5 ÷ 300 A
TIG AC
DYNAMIC TIG
SPEED TIG
COLD TIG
SOFT TIG 5 ÷ 220 A
5 ÷ 220 A
16 ÷ 127 A
16 ÷ 156 A
5 ÷ 300 A
5 ÷ 300 A
5 ÷ 173 A
5 ÷ 212 A
WARNING: This can only be programmed when 4 STROKES or
SWITCH welding mode is activated.
L13 SLOPE UP duration (0,0 ÷ 5,0 sec)
L11 PRINCIPAL welding CURRENT I
1
1806.M AC/DC 2506.M AC/DC
TIG DC 5 ÷ 220 A 5 ÷ 300 A
TIG AC
DYNAMIC TIG
SPEED TIG
COLD TIG
SOFT TIG 5 ÷ 220 A
5 ÷ 220 A
16 ÷ 127 A
16 ÷ 156 A
5 ÷ 300 A
5 ÷ 300 A
5 ÷ 173 A
5 ÷ 212 A
L16 SLOPE DOWN duration (0,0 ÷ 8,0 sec)
L22 FINAL welding CURRENT
1806.M AC/DC 2506.M AC/DC
TIG DC 5 ÷ 220 A 5 ÷ 300 A
TIG AC
DYNAMIC TIG
SPEED TIG
COLD TIG
SOFT TIG 5 ÷ 220 A
5 ÷ 220 A
16 ÷ 127 A
16 ÷ 156 A
5 ÷ 300 A
5 ÷ 300 A
5 ÷ 173 A
5 ÷ 212 A
WARNING: This can only be programmed when 4 STROKES or
SWITCH welding mode is activated.
L17 POST GAS duration (0,5 ÷ 25,0 sec)
WARNING: When the post-gas LED flashes and the LED I
1
is on
at the same time, this means that the welding power source is in
the post-gas stage.
To exit the setting phase, hold the WELDING PARAMETERS SE-
LECTION key (T10) down for about
1 second .
2 - WELDING PARAMETERS with
PULSE mode active:
Pulsed TIG welding allows greater control of the arc and better de-
formation of the material.
The
Welding power source can be used for TIG AC and DC
pulsed welding in 4 different modes:
•
SLOW PULSE
•
FAST PULSE
•
ULTRA FAST PULSE
•
SYN PULSE
WARNING: Pulsation is deactivated automatically for the duration
of the INITIAL and FINAL current.
2A) SLOW PULSE
TIG pulse welding with manual setting of parameters.
WARNING:This can only be programmed when the 3 TIG weld-
ing processes are used.
Press the PULSE key (T5) until the requited pulsation
is active.
Press the WELDING PARAMETERS SELECTION Key
(T10) a number of times to set the following (in addi-
tion to the WELDING PARAMETERS defined as be-
ing “BASIC”):
L20 L21
L15 L14
T10
PULSE
SYN
FAST
SLOW
T5