DINSEO DIX TIG GO 1806.M AC/DC, Руководство по эксплуатации, Страница: 18 / 30

18
Displaying the software
version installed
The Welding power source are fitted with a digital control with
software on board defined in the factory. This software is subject
to continuous evolution and improvement. The software is identi-
fied by a specific number that can be viewed on the DISPLAY (D)
as follows:
1) When the welding power source is off, push and hold the
“MEM” SAVE key down (T1).
2) Start the welding power source by turning the power supply
switch to position I .
3) For a few seconds the DISPLAY (D) shows the type of soft-
ware on board (e.g. b01) where:
•
b indicates the welding power source model.
•
01 indicates the VERSION of the software installed
PULSE
SYN
FAST
SLOW
WAVE
Ø
SWITCH
SWITCH
I
1
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE
I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
T1
D
DIX TIG GO
1806.M
Electrode welding (MMA)
1) Start the welding power source by turning the power supply
switch to position I .
2) WELDING PROCESS SELECTION
Push the WELDING PROCESS SELECTION key (T7) to se-
lect the ELECTRODE welding processes for welding with
“HOT START” or “ARC FORCE” devices that can be pro-
grammed by the user.
3) Turn the ENCODER Knob (E) until the DISPLAY shows the
CURRENT VALUE at which you wish to weld, in relation to
the diameter of the electrode you are using.
I
I
b PULSE
SYN
FAST
SLOW
WAVE
Ø
DIX TIG GO
1806.M
I
1
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
SWITCH
SWITCH
T7
T10
E
D
4) WELDING PARAMETERS SELECTION
To refine the weld quality, the following parameters can be set
by pushing the WELDING PARAMETERS SELECTION key
(T10) in succession:
•
HOT START - This increases the welding current, in per-
centage terms, for a time interval that can be set at the start
of the welding process, thereby reducing the risk of poor fu-
sion at the start of the joint (
L9 - HOT START - 00-100).
•
MMA ARC FORCE - Regulates, in percentage terms, the
dynamic characteristics of the arc ( L10 - ARC FORCE -
00-100).
•
PRINCIPAL welding CURRENT I
1
( L11 ):
1806.M AC/DC 2506.M AC/DC
10 ÷ 180 A 10 ÷ 250 A
I
1
HOT
START
ARC
FORCE
I
b
T
b
T
p
f
I
p
I
2
PULSE
L11 L9 L10
SWITCH
The value for the welding parameters can be regulated using
the ENCODER Knob (E).
I
1
PULSE
SYN
FAST
SLOW
WAVE
Ø
I
1
T10
D
E
DIX TIG GO
1806.M
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
SWITCH
SWITCH
5) To exit these functions hold the WELDING PARAMETERS
SELECTION key (T10) down for about 1 second, after which
the DISPLAY INDICATION LED switches on and the welding
power source is once again ready to weld at the current indi-
cated on the DISPLAY (D).
6) Once the all the selections/regulations indicated above have
been made, welding can begin.
7) During the welding process the DISPLAY (D) shows the real
Amps (A) at which the operator is actually welding.
TIG “AC” welding
1) Start the welding power source by turning the power supply
switch to position I .
2) Push the WELDING PROCESS SELECTION key (T7) to se-
lect the TIG “HF AC” welding processes for TIG welding in
alternating current with high frequency (HF) ignition.
3) ELECTRODE DIAMETER SELECTION
Select the diameter of the electrode to achieve the best control
of ignition in a synergic manner. Selection is done by pushing
the ELECTRODE DIAMETER Key (T8) (ELECTRODE DIAM-
ETER LED flashing) and using the ENCODER Knob (E) to
regulate the value indicated on the DISPLAY (D).
PULSE
SYN
FAST
SLOW
WAVE
Ø
DIX TIG GO
1806.M
I
1
SYN
FAST
SLOW
VRD
HF AC
DC
DC
HF
HOT
START
ARC
FORCE I
b
T
b
T
p
f
I
p
I
2
MEM
PRG
PULSE
PULSE
ULTRA
FAST
WAVE
WAVE
A
V
D
SWITCH
SWITCH
T7
T8
E
To confirm the diameter selected, simply push the ELEC-
TRODE DIAMETER Key (T8) again (ELECTRODE DIAME-
TER LED off).