DINSE DIX GO 1156.M Puls, Руководство по эксплуатации

Страница: 3 / 36

3
- MMA welding:
- “Arc Force” adjustable to select the best dynamic char-
acteristics for the welding arc.
- “Hot Start” adjustable to improve ignition with particu-
larly difficult electrodes.
- Anti-sticking function to avoid the electrodes sticking.
- Vrd (Voltage Reduction Device), which makes it pos-
sible to use the welding power source in environments
where the risk of electric shock or electrocution caused
by arc welding is enormously increased by the pres-
ence of water, humidity, or heat, and particularly where
the ambient temperature exceeds 32°C.
- TIG welding:
- “Lift” type ignition, with TCS “Thermal Control Start” de-
vice to further reduce tungsten inclusions.
- Exclusive SWS “Smart Welding Stop” system at the
end of TIG welding. Lifting up the torch without switch-
ing off the arc will introduce a SLOPE DOWN and it will
switch off automatically.
Technical data
The general technical data of the system are summarized in
table 1.
Usage limits (IEC 60974-1)
The use of a welder is typically discontinuous, in that it is made
up of effective work periods (welding) and rest periods (for the
positioning of parts, the replacement of wire and underflush-
ing operations etc. This welder is dimensioned to supply a I
2
max nominal current in complete safety for a period of work of
X% of the total usage time. The regulations in force establish
the total usage time to be 10 minutes. The work cycle is con-
sidered to be X% of this period of time. When the work cycle
permitted is exceeded a trip switch trips, which protects the
welding welding power source’s internal components against
dangerous overheating and prevents incorrect functioning of
the welding power source. After several minutes the overheat
cut-off rearms automatically and the welder is ready for use
again (Automatic reset error). This equipment is built to have
a protection level of IP 23 S, which means:
•
That it is protected against the penetration of solid foreign
bodies with diameters in excess of Ø 12 mm.
•
That it is protected against water spray hitting the surface
with an angle of incidence up to 60°.
•
That the equipment has been tested for withstanding harm-
ful effects due to water getting in when the moving parts on
the equipment are moving.
Table 1
Model
DIX PI GO 1156.M Puls
MIG/MAG TIG MMA
Single-phase input 50/60 Hz
V 230 ± 15%
Mains supply: Z
max
(*) Ω
0,21
Power input (I
2
Max)
kVA 9,7 6,4 7,8
Delayed fuse (I eff)
A 16
Power factor / cosφ
0,64 / 0,99 0,64 / 0,99 0,64 / 0,99
Efficiency degree
η
0,83 0,8 0,83
Voltage without load
V 60
Current range
A 10 ÷ 200 5 ÷ 175 10 ÷ 150
Duty cycle @ 100% (40°C)
A 100 100 90
Duty cycle @ 60% (40°C)
A 115 115 110
Duty cycle @ X% (40°C)
A 200 (15%) 175 (20%) 150 (25%)
Wires diameter
mm 0,6 - 1,2 - -
Spool
Diameter / Weight
mm / kg 200 / 5
- -
N° rollers
2 - -
Power output of feeder motor
W 40 - -
Rated wire feeding speed
m/min 1 - 20 - -
MMA electrodes
mm - - 1,6 - 3,2
TIG electrodes
mm - 1,0 - 3,2 -
Protection gas
•
Carbon dioxide
•
Pure Argon
•
Argon - Carbon dioxide
- Oxygen
•
Argon and Carbon
dioxide blends
- -
Standards
IEC 60974-1 - IEC 60974-5 - IEC 60974-10 -
Protection class
IP 23 S
Insulation class
H
Dimensions
mm 500 - 425 - 220
Weight
kg 16
(*) Mains supply Z
max
: maximum impedance value allowed for the grid according to the EN/IEC 61000-3-11 standard.
WARNING: This equipment does not comply with EN/IEC 61000-3-12. If it is connected to a public low voltage system, it is the responsibility
of the installer or user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment may
be connected.