manualshive.com logo in svg

Dimplex SF3202, Руководство по обслуживанию, Страница: 3 / 21

Поделиться
Скачать
Dimplex SF3202 Скачать руководство пользователя страница 3

SF3202 
 

OPERATION 

 
Electric Fireplace Manual Controls 
A. Manual on/off switch 

1.  The fireplace has a manual power ON/OFF switch located on the control panel of 

the fireplace. 

2.  To operate press the switch once, to turn the unit on.  A red light will illuminate to 

indicate the power is on.  Press the switch again to turn the unit off. 

NOTE: 

When the manual power switch is used the heater will run. 
The manual ON/OFF switch is to be used only when the remote transmitter is OFF. 

B. Flame action control 

Turn the flame action control knob to adjust the flame speed control to the desired level. 

C. Heater override switch 

When the Manual on/off switch is in the on position the heater will run.  Turn the heater 
override switch to the off position to shut off the heater. 

NOTE: 

Ensure that the heater override switch is in the on position for the heater to work with 
the remote control.  

 

 

RESETTING THE TEMPERATURE CUTOFF SWITCH

 

Should the heater overheat, an automatic cut out will turn the heater off and it will not 
come back on without being reset.  It can be reset by switching the MAIN ON/OFF 
SWITCH to OFF and waiting 5 minutes before switching the unit back on.

 

CAUTION 

 

2

If you need to continuously reset the heater, unplug the unit and call Dimplex North 
America Limited at 1-800-668-6663. 

Содержание SF3202






















Отзывы:

Нет отзывов