7207930100R05
INUPCN240V
Convector Heater
PLX Series
Installation Instructions
IMPORTANT INSTRUCTIONS
Please read carefully all the information provided in these
instructions. Keep the instructions in a safe place and if
necessary give them to any future owner.
1. The device may only be installed by an authorized and
qualified technician.
2. The unit may only be used for space heating in enclosed
rooms.
3. Any examination of the heater or repair work may only be
carried out by a qualified electrician.
4. Disconnect the heater from the power supply if it is faulty
or is not used for a long time. Disconnect or shut off the
power at the breaker.
5. Do not cover the heater in any way (risk of fire).
6. Outer surfaces become hot when heater is switched on.
7. The heater must not be operated by children or other
persons not capable of using the appliance in a safe
manner. Children must be prevented from playing with the
appliance.
8. Do not insert any objects into the openings.
9. Do not use the heater in rooms containing flammable
materials (e.g. solvents, etc.).
10. If the heater is switched on automatically, there is a danger
of fire if it has been in any way covered or blocked.
SAVE THESE INSTRUCTIONS
Positioning, Installation, Minimum Clearances
When installed, the heater must be aligned horizontally on
a vertical wall, as shown in the illustration. (Figure 1) The
minimum clearances shown must be complied with. In addition,
a minimum distance of at least 508 mm / 20” must be maintained
in front of the heater.
WARNING:
Do not install the heater where the controls can
be reached by a person bathing or showering.
CAUTION:
The heater must not be located directly beneath
a wall socket outlet.
CAUTION:
Do not place near flammable objects.
Ensure that air can enter and leave the heater freely, at the
inlets below and the outlets above.
The recess box must be accessible for inspection after the
appliance has been mounted.
Wall Mounting
CAUTION:
The original wall brackets supplied attached to
the rear of the unit must be used.
1. Drill mounting holes for the wall brackets. See Figure 1 for
mounting hole locations.
2. Screw the brackets securely to the wall.
Figure 1
3. Hang the heater from the wall brackets using the slits in its
rear wall. (Figure 2)
4. Secure the heater at the top on the wall brackets.
Electrical Connection
All wiring must comply with National Electrical codes and local
codes and utility requirements. This installation should be
entrusted to duly qualified personnel where required by law.
Connect the supply wire into a properly rated recess box.
Consult your local electrical code for applicable wire gauge.
Connect L1 from the power supply to the L1 wire from the unit,
connect the L2 wire from the power supply to the L2 wire from
the unit, and connect the ground to the G wire from the unit.
Anti-Overheat
The heater is protected with a safety device to prevent
overheating. Should the heater overheat due to impeded air
circulation the automatic cutout will turn the heater off. The
heater will reactivate once the heater has cooled.
Keep the air inlets and outlets free of dust to ensure that
Figure 2
MODEL
A
PLX050NN
117 mm / 4.6"
PLX075NN
287 mm / 11.3"
PLX100NN
287 mm / 11.3”
PLX125NN
355 mm / 14.0"
PLX150NN
355 mm / 14.0”
PLX200NN
527 mm / 20.7"
16.9"
(430 mm)
4.1"
(105 mm)
7.25"
(184mm)
2.5"
(64 mm)
5.9"
(150 mm)
MIN
A
4.6"
(118 mm)
10"
(255 mm)
MIN
5.9"
(150 mm)
MIN
16.9"
(430 mm)
5.9"
(150 mm)
MIN
