Installation and Operating Instructions
INDGAUP7RG Issue 0
Girona Panel Heaters
Dimensions
(millimetres)
Model
(
s
)
Watt
A
B
GFP200 W
2.0kW
940
107
GFP200 B
2.0kW
940
107
Important Safety Advice
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
IIMPORTANT – The wall bracket supplied with the
appliance must be used.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
IMPORTANT – If the heater is installed in a room
containing a bath or shower, it must be so installed that
switches and other controls cannot be touched by a
person using a bath or shower.
Do not use outdoors.
Do not locate the heater immediately in front of or below
a fixed socket outlet or connection box.
Do not cover the heater. Do not place material or
garments on the heater, or obstruct the air circulation
around the heater, for instance by curtains or furniture,
as this could cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots
at the top of the heater or the air inlet slots in the base of
the heater.
The heater carries the Warning symbol indicating
that it must not be covered.
WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.
Momentary contact with any part of the heater should
not cause injury.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
Note that due care and consideration must be taken
when using this heater in series with a thermal control,
a program controller, a timer or any other device that
switches on the heat automatically, since a fire risk
exists when the heater is accidentally covered or
displaced.
If the supply cord is damaged, it must be replaced by a
special cord or assembly available from the
manufacturer or its service agent.
Fig. 1
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The heater is fitted with a cable and plug. The length of flexible
cable type H05VV-F size 3 x 1.0mm
2
on all models.
General
The heater is designed for wall mounting on the wall bracket
supplied. It should only be operated when in the upright
position - see
Fig. 1
.
All models are splashproof to IPX4 standard and may be
used in bathrooms, however not in the immediate vicinity of
baths, showers, water connections, wash basins or
swimming pools.
Before connecting the heater check that the supply voltage is
the same as that stated on the heater.
Wall Mounting
IMPORTANT
– The wall bracket supplied with the appliance
must be used. The heater should be positioned observing
the minimum clearances stated around the heater - see
Fig. 1
.
DO NOT
locate the heater immediately below a fixed socket
outlet or connection box.
1.
Remove wall mounting bracket from the back of the
heater by depressing the spring latch at the top of
each bracket - see
Fig. 2
.
2.
Fix the wall bracket securely to the wall through the
four screw holes provided.
3.
Present the heater to the wall bracket, and engage
lower slots in the back with bracket.
4.
Raise the heater to upright position and push the
heater onto bracket to engage top latch.
A
565
B
150
Min.
300 Min.
shelf
150 Min.
D
255 Min.
C
C
D
GFP200W 800
300
GFP200B 800
300
Fig. 2
AUS/NZ
