Dimplex EWT SP16-LED, Руководство пользователя, Страница: 5 / 16

A choice of 1KW or 2KW heat output is provided by the fan
heaters which are concealed within the unit.
The heater can be used remotely or manually - see ‘Operation’.
General features of remote control are:
•Flame picture can be turned On or Off.
•Heat output can be increased or decreased according
to your particular requirements
Please Note: Used in an environment where background
noise is very low, it may be possible to hear the motor which
operates the flame effect. This is normal and should not be a
cause for concern.
Installation
Safety Message
- Sufficient expertise is required for installing
this product. If unsure we recommend that you subcontract
the installation and pay special attention to safety during the
installation.
Wall Installation
Do not connect appliance until properly fixed to the wall
and the Instruction leaflet is fully read. In particular, the
minimum distances must be observed.
For installation of the appliance, care must be taken not to
damage concealed cables.
Please be careful while drilling the holes.
The wall plugs supplied with this product are for use with Block/
Brick built walls only.
This model is designed to be permanently fixed to a wall at
a minimum height of 300mm. The wall bracket must be fitted
horizontally and the cable routed to the bottom right of the
appliance shown as “a” in Fig. 1 .
A height of 600 to 725mm from bottom of the appliance to floor
is recommended for optimum viewing of fuel bed (see Fig. 2
for recommended fixing dimensions).
For optimum viewing mark the top four screw fixing positions
on wall in accordance with the recommended fixing dimensions
- see Fig. 2 . Drill holes with a 6mm drill bit.
Fix the wall bracket using the plugs and screws provided - see
Fig. 3 .
Carefully lift the appliance up ensuring that the top rear ledge
of the appliance engages the wall bracket and is centrally
positioned. - see Fig. 4 .
A bottom fixing bracket is supplied. Fix this bracket to the
bottom of the appliance using the silver screw on the underside.
With the bracket in place mark the location of the hole on the
wall. Then remove the appliance,drill the wall, fit the wall plug
and re-fit the appliance ensuring that you secure it in place by
screwing the bracket to the wall.
Recessed Installation
Please note that this appliance can also be recessed. This
can be installed in a large fireplace opening or a purpose built
wall. See
Fig. 6
for size of recess required and hole fixing
dimensions.
It is essential that this fire is securly fixed to the wall and it is
important that the fixing device chosen is appropriate to the
wall material. Some modern internal building materials may
require specialised fixing devices to provide a safe, secure
installation. If in doubt, please consult a qualified installer.
The wall should be capable of supporting the weight of the
appliance. If the installation of the bracket on the wall is not
sufficiently sturdy, the unit may fall and cause injury or property
damage.
Existing Fireplace
1. Make sure that the fire is located on a flat surface.
2. Seal all draughts and vents to prevent chimney debris from
falling onto the appliance. Do not install into an existing
fireplace that is prone to dampness.
3. Remove the fire front panel by following the steps as
outlined in ‘Front Panel Removal’ section.
4 . Locate the 4 fixing holes,2 top and 2 bottom, position the
fire accordingly, and firmly fix the appliance to the wall using
the appropriate screws - see
Fig. 6
.
5 . Replace the front panel.
New Support Structure Construction
If planning to position your applaince on a purpose built support
structure the following steps must be observed:
1. Place the fire in the desired location to see how it will look
in the room.
2. Mark the desired location for the new support structure in the
room and store the fire in a safe, dry and dust free location.
3.
Using timber studs to support the fire, devise and construct
a suitable means of supporting the product within the wall
partition and provide electrical power for the fire to be HARD
wired. For recommended sizes of height, width and depth of
opening for recess and hole fixing dimensions - see Fig. 6
4. When the structure is complete, remove the front panel of
the fire by following the steps as outlined in ‘Front Panel
Removal’ section.
5. Locate the 4 fixing holes, position the fire accordingly, and
firmly fix using the appropriate screws.
6
. Replace the front panel.
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
The heater is fitted with a flexible cable, size 3 x 1.0mm
2
for
connection to the fixed wiring of the premises through a suitable
connection box positioned adjacent to the heater.
A means for disconnection must be incorporated in the fixed
wiring of the premises in accordance with the wiring rules.
Please consult a qualified electrician for appropriate wiring
requirements.
Front Panel Removal
To remove the front panel please apply the following procedure:
While holding the front panel by its sides with both hands, (1)
carefully tilt the bottom of the frame outwards until free and
then lift the panel up (2) and then away (3) from the main
body - see Fig. 7 .