fInstallation and Operating Instructions
DXFF20TSN & DXFF30TSN Flat Fan Heaters
08/51250/0
Issue 1
Model
(
s
)
Specification
air inlet
DXFF20TSN
2.0kw Switch, Thermostat & Neon
DXFF30TSN
3.0kw Switch, Thermostat & Neon
IMPORTANT - DO NOT USE AS A HAIRDRYER
REGULAR VACUUM CLEANING IS REQUIRED
TO ENSURE PROPER OPERATION (see below)
air outlet
handle
thermostat
knob - see
Fig. 3
heat control
knob - see
Fig. 2
mains neon
Fig. 1
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair
type of rugs, or less than 750mm (30") away from any
overhanging surface. Keep combustible materials such as
drapes and other furnishings clear from the front, sides and
rear of the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of
a bath, a shower or a swimming pool.
DO NOT place the heater directly below a fixed socket outlet.
WARNING: In order to avoid overheating, do not cover
the heater.
The socket-outlet must be accessible at all times to enable
the mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct in any way the air inlet slots
in the top and bottom of the heater, or the air outlet slots
at the front of the heater.
DO NOT operate the heater with the mains lead
overhanging the front outlet grille.
The heater should always be used on a flat, stable surface.
This appliance is not intended for use by children or
other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Warning : In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this appliance must not
be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
THE HEATER CARRIES A WARNING SYMBOL
INDICATING THAT IT MUST NOT BE COVERED.
The instruction leaflet belongs to the appliance and
must be kept in a safe place. If changing owners, the
leaflet must be surrendered to the new owner.
IMPORTANT
– If the mains lead of this appliance is damaged, it
must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
Electrical connection
This heater must be used on an ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
This heater is fitted with a rewirable plug incorporating a 13
amp fuse. In the event of replacing the fuse in the plug
supplied, a 13 amp fuse approved by ASTA to BS 1362 must
be used. If any other type of plug is used, a 15 amp fuse must
be fitted in the plug, the adaptor, or at the distribution board.
IMPORTANT : If the plug is not suitable for your socket, the 13
amp plug should be removed. Before wiring the appropriate
plug, please note that the wires in this mains lead are coloured
in accordance with the following code :
BLUE :
NEUTRAL
BROWN :
LIVE
As the colours of the wires in the mains lead may not correspond
with the coloured markings in your plug, proceed as follows :
Connect the
BROWN
wire to the terminal marked
‘
L
’ or coloured
RED
.
Connect the
BLUE
wire to the terminal marked
‘
N
’ or coloured
BLACK
.
Note :
‘L’ or ‘N’ wire must not be connected to the EARTH
terminal marked
‘E’ or or coloured
GREEN
or
GREEN AND
YELLOW
. If in doubt, consult your electrician.
VERY IMPORTANT ADVICE
NORMAL USE OF YOUR FAN HEATER IN
AREAS WHICH HAVE HIGH LEVELS OF FLUFF,
DUST OR HAIR (e.g. BEDROOMS/DRESSING
AREAS/HAIR
SALONS)
ESPECIALLY
ON
SOLID/LINO COVERED FLOORS, WILL RESULT
IN THE ACCUMULATION OF THESE INSIDE THE
HEATER AT THE BACK OF THE ELEMENT.
IF LEFT TO BUILD UP, IT WILL EVENTUALLY
RESULT IN THE SAFETY CUT-OUT OPERATING
TO PROTECT YOU AND THE HEATER FROM THE
DANGER OF THE PRODUCT OVERHEATING!
IT IS THEREFORE CRITICAL THAT YOU USE A
VACUUM CLEANER TO REGULARLY BLOW
OUT AND CLEAN ANY ACCUMULATION FROM
THE HEATER! (See CLEANING section overleaf
for more detailed instructions on how to do this)
