Digitrax Zephyr xtra Скачать руководство пользователя страница 26

Страница: 26 / 66

www.digitrax.com

6. Press the

Cv-Wr

key to write the address to the decoder. The display will

flicker while the address is programmed and then will show the new address

in the display.
For example, to change the address from the two digit address 03 to the two

digit address 96, press the

lOCO

Key until

Ad2

appears in the display then

use the key pad to enter

and press the

Cv-Wr

key to write the address.

7. When you are finished programming the address, press the

exit

key. You

are now ready to resume normal operations or proceed to programming

other configuration variables.

For convenience the DCS51 will automatically return to the last Programming

mode and CV number when programming is used the next time.

16.3programmingConfigurationvariables Otherthanaddresses

There are many different CVs that have been defined to control the operating

characteristics of your locomotives. Your decoder manual has a complete list-

ing of CVs that are available in specific decoders, what they do and suggested

values for each CV. Programming these CVs is simple:
1. Be sure that only the locomotive you want to program is on the program-

ming track (if using Operatiosn mode the loco will need to be on the main-

line).

2. Press the

prOg

Key to enter programming mode. The DCS51 will display

one of the programming modes available. Digitrax recommends the Direct

Mode when you are using the programming track. As you press the

prOg

Key repeatedly, you will cycle through the following choices:

dir, OPS,PAGE, PHYS,

Once the mode you want to use is on the screen you can go to step 3.
For example, to use Direct mode stop pressing the

prOg

Key when the fol-

lowing screen appears:

3. Press the

Key and you will see

followed by the last CV number used

by the DCS51. The

“t”

indicates that you are in Direct programming mode.

4. Enter the CV number you want to program. For example, if you want to set

up acceleration which is controlled by CV03, use the keypad to enter

5. Press the

Cv-rD

key to to read back the data value currently programmed

into the decoder for the CV selected. Your screen will show something like

this:

Содержание Zephyr xtra



































































Результаты поиска

Содержание Zephyr xtra

Отзывы:

Похожие инструкции для Zephyr xtra

Бренды по названию

Популярные бренды

Digitrax Zephyr xtra, Руководство пользователя

Результаты поиска

Содержание Zephyr xtra

Отзывы:

Похожие инструкции для Zephyr xtra

Бренды по названию

Популярные бренды