5MP model
2.1MP/1080p model
DWC-MF5Wi4TWDMP
DWC-MF2Wi4TWDMP
Attention:
This document is intended to serve as a quick reference page for
the initial setup. It is recommended that the user read the entire instruction
manual for complete and proper camera usage.
Tel: 866-446-3595 / 813-888-9555
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
WHAT’S IN THE BOX
Quick Setup and
Download Guides
1 set
Moisture Absorber
and Guide
(Recommended)
1 set
Star Wrench (T-20)
1
Mounting Bolt and
Nuts - 2pcs
1 set
Mounting Template
for Bolt and Nuts
Installation
1
Screws and Plastic
Anchors – 3pcs
1 set
Mounting
Template for Plate
Installation
1
Mounting Plate
1
Waterproof Cap
and Rubber Rings
(Black: ø0.15”
(ø4mm), White:
ø0.19” (ø5mm))
1 set
Quick Start Guide
Quick Start Guide
NOTE:
Download all your support materials and tools in one place
1. Go to:
http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’
search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click
‘Search’
. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
STEP 2 – POWERING THE CAMERA
Pass the wires through the mount bracket and make all necessary
connections.
1. NETWORK CONNECTIONS – If you are using a PoE Switch, connect
the camera using an Ethernet cable for both data and power.
2. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
Part number
Power Requirements
Power Consumption
DWC-MF5Wi4TWDMP
DC 12V, PoE IEEE 802.3af
Class 3
(Adapter not included).
DC12V: max 5.9W
PoE: max 7.2W
DWC-MF2Wi4TWDMP
DC 12V, PoE IEEE 802.3af
Class 2
(Adapter not included).
DC12V: max 4.0W
PoE: max 5.5W
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply
Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.49A
(DWC-MF5Wi4TWDMP) and 0.33A (DWC-MF2Wi4TWDMP) min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with the
output evaluated as a Limited Power Source as defined in UL60950-
1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
7. For the installation process, remove the dome cover from the
camera module by loosening the three (3) screws on the dome. Use
the wrench provided with the camera.
8. Install the moisture packet in the base of the camera’s lens.
a. Remove the moisture absorber from
the packaging.
b. Cut the card and folder along
the dotted line.
c. Place the moisture
absorber around the
camera’s lens module.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Reset Button
Poron Ring
9. Remove the protective film
between
the dome and the camera module.
10. Remove the Poron Ring before
placing the dome back on the
camera. When attaching the dome
back, align the line on the dome
with
the one on base of the camera.
11. Using the mounting template sheet
or the camera itself, mark and drill
the necessary holes in the wall or
ceiling.
WARNING:
It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
NOTE:
The camera will generate enough heat to dry moisture
during operation. In most cases it will not need the
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.