Digital Projection Mercury Quad Series Скачать руководство пользователя

Страница: 35 / 130

page 27

Digital Projection Mercury Quad Series

Connection Guide

SIGNAL INPUTS

Rev A March 2017

3D connections

3D sources up to 60Hz requiring frame doubling and left/right interleaving

1. Connect to either of the following inputs on the connection panel:

•

HDMI 1

•

HDMI 2

•

HDBaseT

2. Set

3D Format

in the

menu to match the format of the incoming signal. Choose from

Auto

Side by Side (Half)

and

Top and Bottom

The

Frame Packing

format is automatically detected by the projector.

Frame sequential 3D sources up to 120Hz

•

Connect to the DisplayPort input.
The

Frame Sequential

format is automatically detected by the projector and is supported on the DisplayPort input only.

Dual Pipe 3D

1. Connect the left eye output to the

HDMI 1

socket and the right eye output to the

HDMI 2

socket.

2. Set

3D Format

in the

menu to

Dual-Pipe

Notes

For a complete listing of all

supported signal input modes, see

Appendix B: Supported Signal

Input Modes

in the

Reference

Guide

For a complete listing of pin

configurations for all signal and

control connectors, see

Appendix

C: Wiring Details

in the

Reference

Guide

HDBaseT

HDMI 1 / Dual Pipe LEFT

HDMI 2 / Dual Pipe RIGHT

DisplayPort

Содержание Mercury Quad Series



































































































































Результаты поиска

Содержание Mercury Quad Series

Отзывы:

Похожие инструкции для Mercury Quad Series

Бренды по названию

Популярные бренды

Digital Projection Mercury Quad Series, Инструкция по установке и быстрому запуску

Результаты поиска

Содержание Mercury Quad Series

Отзывы:

Похожие инструкции для Mercury Quad Series

Бренды по названию

Популярные бренды