Digital Projection Mercury Quad Series Скачать руководство пользователя | Manualshive

Страница: 34 / 130

background image

page 26

Digital Projection Mercury Quad Series

Connection Guide

SIGNAL INPUTS

Rev A March 2017

EDID on the HDMI and DisplayPort inputs

If you are using a computer graphics card or another source that obeys the EDID protocol, the source will automatically configure itself to suit

the projector.
Otherwise refer to the documentation supplied with the source to manually set the resolution to the DMD™ resolution of the projector or the

nearest suitable setting. Switch off the source, connect to the projector, then switch the source back on again.

Using HDMI/DisplayPort switchers with the projector

When using an HDMI/DisplayPort source switcher with the projector, it is important to set the switcher so that it passes the projector EDID

through to the source devices. If this is not done, the projector may not be able to lock to the source or display the source correctly as its

video output timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-through or clone mode.

See your switcher’s manual for information on how to set this mode.
Additionally, sources which use HDCP encryption may not display properly when connected to the projector via a switcher. Refer to the

switcher’s manual for more information.

1

Sources

2

Switcher

3

Projector

Notes

The EDIDs in the switcher should be the same as the one in the projector.

1

3

2

EDID

EDID

EDID

EDID

«
...
32
33
34
35
36
...
»

Содержание Mercury Quad Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Mercury Quad Series

REALIS WUX10 MARK II D

Бренд: Canon Страницы: 12

Бренд: VIVIBright Страницы: 2

GR 0021 HMI 1200

Бренд: Griven Страницы: 16

Video Xtreme VX-40d

Бренд: Runco Страницы: 102

Projector Accessories

Бренд: AccuScreens Страницы: 12

Бренд: Sagem Страницы: 30

Бренд: M-system Страницы: 2

Бренд: Barco Страницы: 74

Бренд: Acer Страницы: 56

Бренд: Acer Страницы: 63

Бренд: Acer Страницы: 57

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 186

LITOL LTM-125RF

Бренд: Mitsubishi Electric Страницы: 2

Бренд: RocketFish Страницы: 2

Бренд: Sanyo Страницы: 2

Бренд: Sanyo Страницы: 4

Бренд: Sanyo Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды