Digital Projection Mercury Quad Series Скачать руководство пользователя страница 27

Страница: 27 / 130

page 19

Digital Projection Mercury Quad Series

Installation and Quick-Start Guide

OPERATING THE PROJECTOR

Rev A March 2017

Operating The Projector

Switching the projector on

1. Ensure a lens is fitted. Connect the power cable between the mains supply and the projector. (See

Connecting the power supply

above.) Switch on at the switch next to the power connector.

2. The

POWER

indicator lights red to signal that the projector is in STANDBY mode. Press one of the following buttons:

•

On the remote control, the

button

•

On the projector control panel, the

POWER

button.

The fans begin working, then the

POWER

indicator begins flashing green. When the flashing stops, the

POWER

and

LIGHT

indicators

both light steady green. The projector is switched on.

Switching the projector off

1. Press

OFF

on the remote control or

POWER

on the control panel, then press again to confirm your choice.

The

POWER

indicator on the control panel will start flashing amber, the system will go out and the cooling fans will run for a short time

until the

POWER

indicator goes stready red to indicate that the projector has entered STANDBY mode.

2. If you need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect

the power cable from the projector.

Notes

See also

Connecting The Power

Supply

earlier in this guide.

Use only the power cable

provided.

Ensure that the power outlet

includes a ground connection as

this equipment MUST be earthed.

Handle the power cable carefully

and avoid sharp bends. Do not

use a damaged power cable.

Содержание Mercury Quad Series



































































































































Результаты поиска

Содержание Mercury Quad Series

Отзывы:

Бренды по названию

Популярные бренды

Digital Projection Mercury Quad Series, Инструкция по установке и быстрому запуску

Результаты поиска

Содержание Mercury Quad Series

Отзывы:

Бренды по названию

Популярные бренды