background image

-1-

• Be sure to confirm that the PL unit’s power cord is disconnected prior to

installing PL-FD210, in order to prevent electrical shock.

• Do not attempt to modify the PL-FD210, due to the danger of fire or electrical

shock.

• Prior to installing the PL-FD210, be sure to read this Installations Guides’ “2.

Installation” section completely to insure that this unit is correctly installed.

To Prevent Accidents

• Since the PL-FD210 is a precision instrument, be sure that it is neither hit by nor

pressed strongly against another object.

• Be sure that water, liquids, or metal particles are not allowed to contact  or enter

this unit. Either of these may cause either a breakdown or an electrical shock.

• Do not install or operate this unit in a location where there is direct sunlight,

excessive heat, dust or vibration.

• Do not store or operate this unit near chemicals, or where there are chemical

fumes.

• Do not use the PL-FD210 in locations where corrosive gasses are present.
• To prevent damage to file data, be sure to shut down the unit's OS before turning

OFF the main power.

Warning - Safety Precautions

The PL-FD210 (FDD Unit) is an internally mounted 3.5 inch floppy disc drive
unit, designed for use with Proface’s Panel Computer, hereafter referred to as
the “PL.”

Corresponding PL unit: PL-X900 Series Units(4Slot type), PL-X920 Series Units

(4-Slot type)

All product names used in this document are the trademarks of their respective
manufacturers.
Pro-face: Digital Electronics Corporation

!!!!!

PL-FD210

Installation Guide

Содержание PL-FD210








Отзывы:

Похожие инструкции для PL-FD210