Digital-Ally DVM-800 Скачать руководство пользователя страница 8

Страница: 8 / 56

Digital Ally, Inc.

Device Configuration

3-1

DVM-800 Operation Guide

860-00186-00 Rev L

Go Back To

Table of Contents

The DVM-800 is shipped with a default configuration so it can be used immediately after

installation. However, many parameters can be configured and saved as an activation

file. The activation file is saved to a local hard drive or external SD card. The DVM-800

is activated and configured using Digital Ally’s VuVault

back-office software. Use the

“VuVault Installation Guide”

to install the VuVault software. Once installed, follow the

instructions in this section to configure and activate your DVM.

ONCE THE DESIRED SETTINGS HAVE BEEN ENTERED, CLICK SAVE AND

PROCEED TO SECTION 3.11 TO ACTIVATE YOUR SD CARD.

3.1 Default Configuration

If the unit has never been activated, it will use the following default settings preset from

the factory.

•  User Name/Password login entry
•  English language
•  Central Standard Time
•  Date format: mm/dd/yy
•  Time format: 12 hour
•  Daylight saving time (DST) enabled
•

STANDBY mode, 30 second pre-event recording turned on.

• External triggers: emergency lights and wireless microphone
•

Audio is off for pre-event, audio is on during event recording

•  LCD Auto Mode
•  60 second entry timeout
•  Recording resolution is D1 @ 30 frames per second
•  ECA

(Evidence Capture Assurance

) is enabled

• Dual Channel Recording
•

All profiling screens disabled

• Accelerometer disabled
• 30 minute ignition shutdown timer

Section 3

Device Configuration

Содержание DVM-800

























































Результаты поиска

Содержание DVM-800

Отзывы:

Похожие инструкции для DVM-800

Бренды по названию

Популярные бренды

Digital-Ally DVM-800, Руководство по эксплуатации

Результаты поиска

Содержание DVM-800

Отзывы:

Похожие инструкции для DVM-800

Бренды по названию

Популярные бренды