manualshive.com logo in svg

Digi XBee Cellular LTE Cat 1, Руководство пользователя, Страница: 63 / 91

Поделиться
Скачать
Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 63

AT commands

Firmware version/information commands

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

63

Default

0x64 (10 seconds)

GT (Guard Times)

Set the required period of silence before and after the command sequence characters of the
Command mode sequence (

GT

+

CC

+

GT

). The period of silence prevents inadvertently entering

Command mode.

Parameter range

0x2 - 0x576 (x 1 ms)

Default

0x3E8 (one second)

Firmware version/information commands

The following AT commands are firmware version/information commands.

VR (Firmware Version)

Reads the firmware version on a device.

The firmware version returns four hexadecimal values (2 bytes)

ABCD

. Digits

ABC

are the main release

number and

D

is the revision number from the main release.

B

is a variant designator where

0

means

standard release.

Parameter range

0 - 0xFFFF [read-only]

Default

Set in firmware

VL (Version Long)

Shows detailed version information including the application build date and time.

Parameter range

N/A

Default

Set in firmware

HV (Hardware Version)

Display the device's hardware version number.

Read the device's hardware version. Use this command to distinguish between different hardware
platforms. The upper byte returns a value that is unique to each device type. The lower byte indicates
the hardware revision.

Содержание XBee Cellular LTE Cat 1




























































































Отзывы:

Нет отзывов