manualshive.com logo in svg

Digi XBee Cellular LTE Cat 1, Руководство пользователя, Страница: 61 / 91

Поделиться
Скачать
Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 61

AT commands

I/O sampling commands

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

61

Parameter Description

1

Fan enable. Output is low when the XBee Cellular Modem is sleeping, turning an
attached fan off when the cellular component is in a power saving mode, and also
during Airplane Mode

3

Reserved

4

Reserved

5

Reserved

Default

0

I/O sampling commands

The following AT command configures I/O sampling parameters.

TP (Temperature)

The current module temperature in degrees Celsius in 8-bit two’s compliment format. For example
0x1A = 26°C, and 0xF6 = -10°C.

Parameter range

This is a read-only parameter

Default

N/A

SM (Sleep Mode)

Sets or reads the sleep mode of the device.

The sleep mode determines how the device enters and exits a power saving sleep.

Parameter range

0, 1, 4, 5

Parameter Description

0

Normal. In this mode the device never sleeps.

1

Pin Sleep. In this mode
the device honors the SLEEP_RQ pin. Set

D8 (DIO8/SLEEP_REQUEST)

to the sleep

request function:

1

.

4

Cyclic Sleep. In this mode
the device repeatedly sleeps for the value specified by

SP

and spends

ST

time awake.

5

Cyclic Sleep with Pin Wake. In this mode the device acts as in Cyclic Sleep but does not
sleep if the SLEEP_RQ pin is inactive, allowing the device to be kept awake or woken by
the connected system.

Содержание XBee Cellular LTE Cat 1




























































































Отзывы:

Нет отзывов