manualshive.com logo in svg

Digi XBee Cellular LTE Cat 1, Руководство пользователя, Страница: 59 / 91

Поделиться
Скачать
Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 59

AT commands

I/O settings commands

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

59

AP (API Enable)

The API mode setting. The device can format the RF packets it receives into API frames and send
them out the UART. When API is enabled the UART data must be formatted as API frames because
Transparent mode is disabled. See

Modes

for more information.

Parameter range

0x00 - 0x05

Parameter

Description

0x00

API disabled (operate in Transparent mode)

0x01

API enabled

0x02

API enabled (with escaped control characters)

0x03

N/A

0x04

N/A

0x05

Bypass mode

Default

0

I/O settings commands

The following AT commands are I/O settings commands.

Sets or displays the DIO6/RTS pin configuration (pin 16).

Parameter range

0 - 1

Default

0

Sets or displays the DIO7/CTS pin configuration (pin 12).

Parameter range

0 - 1

Default

1

D8 (DIO8/SLEEP_REQUEST)

Set or read the DIO8/DTR/SLP_RQ pin configuration (pin 9).

Содержание XBee Cellular LTE Cat 1




























































































Отзывы:

Нет отзывов