Digi XBee Cellular LTE Cat 1 страница 33 Скачать руководство пользователя

Страница: 33 / 91

Hardware

Antenna connections

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

Pin

Name

Direction

Default

Description

PWM1 / DIO11

Either

PWM Output 1 / Digital I/O
11

[reserved]

Do not connect

DTR / SLEEP_RQ/ DIO8

Pin Sleep Control Line or
Digital I/O 8

GND

Ground

DIO4

Either

Digital I/O 4

CTS / DIO7

Either

Output

Output Clear-to-Send Flow
Control or Digital I/O 7

ON /SLEEP/DIO9

Output

Module Status Indicator or
Digital I/O 9

VREF

Unused

This line is not connected.
It is used on other XBee
products.

Associate / DIO5

Either

Output

Associated Indicator,
Digital I/O 5

RTS / DIO6

Either

Disabled

Input Request-to-Send
Flow Control, Digital I/O 6

AD3 / DIO3

Either

Disabled

Analog Input 3 or Digital
I/O 3

AD2 / DIO2

Either

Disabled

Analog Input 2 or Digital
I/O 2

AD1 / DIO1

Either

Disabled

Analog Input 1 or Digital
I/O 1

AD0 / DIO0

Either

Input

Analog Input 0, Digital I/O
0

Pin connection recommendations

The only required pin connections are VCC, GND, DIN, DOUT, RTS, DTR and RESET. Firmware updates
require access to these pins.

Antenna connections

CAUTION!

The XBee Cellular Modem will not function properly with only the secondary

antenna port connected!

The XBee Cellular Modem has two U.FL antenna ports; a primary on the upper left of the board and a
secondary port on the upper right, see the drawing below. You must connect the primary port and the

Содержание XBee Cellular LTE Cat 1




























































































Результаты поиска

Содержание XBee Cellular LTE Cat 1

Отзывы:

Похожие инструкции для XBee Cellular LTE Cat 1

Бренды по названию

Популярные бренды

Digi XBee Cellular LTE Cat 1, Руководство пользователя

Результаты поиска

Содержание XBee Cellular LTE Cat 1

Отзывы:

Похожие инструкции для XBee Cellular LTE Cat 1

Бренды по названию

Популярные бренды