Digi 70002405 Скачать руководство пользователя страница 125

Страница: 125 / 163

Configure the device using the ConnectPort LTS web interface

Administration

Digi ConnectPort LTS User Guide

125

3. (Optional) Choose one or both of the following options:

To keep the network settings for the device, such as the IP address, select the

Keep network settings

check box.

To reset the serial port settings only, select the

Restore Only Serial Port Settings

check

box.

4. Click

Restore

Reset the factory settings on a

ConnectPort LTS

product using the Reset button

To reset the factory settings on a ConnectPort LTS product using the Reset button:

1. Locate the

Factory Reset

button on the front of device, as shown in the following image.

2. Gently press the Factory Reset button with a non-conducive, small diameter tool (such as wood

or plastic) with a blunt end. Do not use a sharp-ended tool or the button could be damaged.

3. Hold down the

Factory Reset

button for 2~3 seconds and then release it.

4. Check the status of the

Ready

LED. When the restoration is complete, the

Ready

LED will turn

on again.

System information

The System Information page displays general system information about the ConnectPort LTS device.
Technical support uses this information to troubleshoot problems. To display these pages, go to

Administration

System Information

General

The General page displays the following general system information:

Model

: The model of the ConnectPort LTS product.

Ethernet MAC Address

: A unique network identifier required for all network devices. The MAC

address appears on a sticker on the Digi device and consists of 12 hexadecimal digits, usually

starting with 00:40:9D.

Firmware Version

: The current firmware version running in the Digi device. Use this

information to locate and download new firmware. You can download firmware updates from

the

Digi Support site

Bios Version

: The current boot code version running in the Digi device.

POST Version

: The current Power-On Self Test (POST) code version running in the Digi device.

CPU Utilization

: The amount of CPU resources the Digi device uses.

Up Time

: The amount of time the Digi device has been running since it was last powered on or

rebooted.

Содержание 70002405




































































































































































Результаты поиска

Содержание 70002405

Отзывы:

Бренды по названию

Популярные бренды

Digi 70002405, Руководство пользователя

Результаты поиска

Содержание 70002405

Отзывы:

Бренды по названию

Популярные бренды