Digi 70002405 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 163

background image

Configure the device using the ConnectPort LTS web interface

Management

Digi ConnectPort LTS User Guide

118

specific behavior, and describes how to load and run Python programs onto Digi devices, and run
sample Python programs.

Python support forum on www.digi.com

Find answers to common questions and exchange ideas and examples with other members of the Digi
Python development community at:

www.digi.com/support/forum/categories/python

RealPort configuration

Install and configure RealPort software on each computer that uses the RealPort ports on the Digi
device. The RealPort software is available for downloading from the Digi Support site. For complete
information on installing and using RealPort software, see RealPort Installation Guide on the

Install RealPort software

To install RealPort software from the Digi Support site:

1. Go to the

ConnectPort LTS

support page.

2. Click

Product Support

>

Drivers

.

3. From the

Operating System Specific Drivers

list box, select your operating system. A list of

available downloads and release notes for your operating system appears.

4. Click the link for the RealPort zip file and save it to your computer.

5. Extract the files from the RealPort zip file and run the RealPort setup wizard.

RealPort Settings

Use the

RealPort Configuration

page to configuring the RealPort application. The available settings

are as follows:

n

RealPort Settings

:

l

Enable Keep-Alives

: Enables the sending of RealPort keep-alives. RealPort protocol sends

keep-alive messages approximately every 10 seconds to connected devices indicating the

connection is still alive. RealPort keep-alives are different from TCP keep-alives, which are

done at the TCP layer.

Note that RealPort keep-alives generate additional traffic which may be undesirable in

situations where traffic is measured for billing purposes.

l

Enable Exclusive Mode

: Exclusive mode allows a single connection from any one RealPort

client ID. If you enable this setting and a subsequent connection occurs that has the same

source IP as an existing connection, the existing connection is forcibly reset under the

assumption that it is stale.

Management

Use the

Management

menu to view and manage connections and services for the ConnectPort LTS

product.

«
...
116
117
118
119
120
...
»

Содержание 70002405




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 70002405

Бренд: IBM Страницы: 64

BladeCenter HS23

Бренд: IBM Страницы: 36

OfficeConnect 3C19500

Бренд: 3Com Страницы: 52

Бренд: NAIM Страницы: 16

Бренд: Xantech Страницы: 52

SUPERSERVER 6027TR-H71FRF

Бренд: Supero Страницы: 118

Бренд: PRIMERGY Страницы: 87

Бренд: Intel Страницы: 32

IDS-5042 Series

Бренд: ORiNG Страницы: 67

Бренд: Eneo Страницы: 94

UniServer R4300 G6

Бренд: H3C Страницы: 542

Бренд: QNAP Страницы: 39

Бренд: XtendLan Страницы: 54

ProxyServer MTPSR1-100

Бренд: Multitech Страницы: 54

LANTIME IMS-M500

Бренд: Meinberg Страницы: 63

Бренд: Skybox Securoty Страницы: 73

Бренд: Cooper Bussmann Страницы: 94

Бренд: Supero Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды