Diamond SmartLyte Скачать руководство пользователя страница 51

Страница: 51 / 81

4 Description of Modules

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 51 of 81

4.3.4.

Graphic Printer CN-A4060

A graphics printer with 192 dots of a TP series has improved the quality and the speed of

printing. The new schematic printer allows the selection of three different fonts and has a

speed 6 times faster than the previous generation.

Note: Graphics Display is not compatible as direct replacement with previous

generation.

Shielding and Grounding in SMARTLYTE

Beside the shield for eliminating the internal noise from the power supply, the entire

SMARTLYTE is equipped with a protective shield to prevent the influence of magnetic

fields, and other noise sources in the laboratory. The internal protective shield creates a

“Faraday Cage”

that protects instrument measurements from outside noise. This shield

is also grounded with a grounding wire in the power receptacle in the power switch input.

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды