Diamond SmartLyte Скачать руководство пользователя страница 50

Страница: 50 / 81

4 Description of Modules

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 50 of 81

Temperature Sensor circuit

This circuit creates a temperature –depended voltage which is converted by software to

degree C. R190 can be adjusted to correct temperature setting.

Analog Channel and A/D Converter

The analog inputs from the amplifiers are connected to IC U21 and U22 ADC1 and

ADC2 converters. ADC 2 is in the schematic for future developments.

JP Connector explanation in the CPU board.

In order to fulfill all responsibilities of the CPU board and the program installed on it, is

equipped with a number of connectors to interface it with all peripherals. The description

of the JP connectors is as below:

JP1 - Graphic printer connector

JP2- NA

JP3 - Power connector receptacle.

JP4 - Display connector

JP5 – Valve board connector

JP6- NA

JP7 – Serial DB9 RS232 Connector

JP8 – USB1 Connector

JP9 – USB 2 Connector

JP10- RFID connector

JP11- JTAG connector

4.3.2.

Valve Board CN-A4018

The valve board contains the LED array used to illuminate the measuring chamber and

the interconnectors used for all solenoids, the peristaltic pump and the door sensor. A

ribbon cable from the CPU Board supplies the electrical connection for each signal

through connector JP5.

4.3.3.

Display Board CN-A4017/CN-A4059

The graphic display module TH16032A has a 160x32 resolution. The backlight is

adjustable and allows for changing the contrast. In the same board are all connection for

YES and NO buttons as well sample sensor and temperature sensor. The connection of

the display board with CPU board is done through ribbon cable connected to JP4 in the

CPU board. The new display board is equipped with two potentiometers for controlling

the backlight and the contrast in the display.

Note: Graphics Display is not compatible as a direct replacement with previous

generation.

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды