Diamond SmartLyte Скачать руководство пользователя страница 34

Страница: 34 / 81

4 Description of Modules

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 34 of 81

4.1.3.

Electrode Tray Assembly

This assembly is comprised of the electrode tray

, CN-A4011

, and the sample sensor,

AV-

BP5036D.

To remove the electrode holder assembly from the analyzer, first unplug the sample

intake tubing on the right side of the assembly where the sample sensor is located. Then

disconnect the sample sensor cable, unplug the reference solution tubing connector and

last, disconnect the waste tube (green tag) from the left side of the electrode tray. The

electrode tray assembly can now be removed by pressing the two plastic tabs on the right

and left side of the module and sliding the module towards you. Continue to press the

plastic tabs to completely release the tray and remove the assembly from the analyzer.

The sample sensor (on the right) and the electrode locking mechanism can be removed

and replaced by removing the screws on the underside of the tray. The Illustrated Parts

List in Section 8 provides a detailed reference of the parts of this assembly.

Fig. 4-3

4.1.4.

Peristaltic Pump Rotor CN-A4014

Replacement of rotor assembly of the peristaltic pump can be accomplished by

removing the pump tubing and firmly pulling the rotor assembly away from the

instrument. To replace the rotor assembly, align the rotor with the flat on the motor

shaft and press the replacement roller into position.

Fig. 4-4

Sample Sensor

Electrode Tray

Peristaltic Pump

Rotor

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды