Diamond SmartLyte Скачать руководство пользователя страница 27

Страница: 27 / 81

3 Software Operation

ECO 9085 SOP05-5038F Rev.05 Effective Date: 12/06/18 Page 27 of 81

3.2.

Service Menu

The SERVICE MENU (mode provides a menu of service check functions to assist in
failure diagnosis and identification. A logic flow chart is provided for reference of the
sequences included in the SERVICE MENU mode.

CHECK ELECTRODES

This mode allows for the measurement and display of electrode voltages.

STD A, STD B

or an external sample can be measured to determine electrode performance and provide

measurement data useful in locating electrode calibration faults. Each electrode

configuration will be displayed and the electrode voltage associated with the sample type

selected can be observed.

Example Displays:

Std. A: Na=1582 Std. B: Na=237

K= 654 Cl=-904 K=-988 Cl=647

Ext: Na=1321

K=-598 Cl=-127

CHECK SAMPLE SENSOR

In this mode, the sample sensor output is displayed which is useful for electrical

adjustment or for troubleshooting sample sensor faults. A dry sample sensor should

display a value of approximately 100 with a range of 80 to 120. After verifying a dry

sensor, aspiration of a clear fluid (i.e., water) should increase the displayed value by at

least 40 units.

Example Display:

DRY 80 -120: 102 External: 153

YES=Pump/No=Exit Pump: NO=OFF

Содержание SmartLyte


















































































Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte

Отзывы:

Бренды по названию

Популярные бренды