manualshive.com logo in svg

Diamond SmartLyte Plus, Руководство по обслуживанию

Поделиться
Скачать
Diamond SmartLyte Plus Скачать руководство пользователя страница 7

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 7 of 58 

 

1.  Introduction 

The Service Manual for the SmartLyte

®

 Plus Electrolyte Analyzer contains the technical information 

needed to ensure easy fault identification. This manual is intended to be complementary to the Operator's 
Manual where detailed instructions for operation, maintenance and troubleshooting are provided. 
 
As for all clinical instrumentation, a thorough understanding of the principles of operation is prerequisite to 
attempting service of this product. Training along with experience will enhance the use of this manual. 
 
Service and repair of the SmartLyte

®

 Plus analyzer should be performed only by qualified repair 

technicians. Care should be taken when removing the covers as hazardous voltages are exposed. Use 
only accepted electronic check procedures and static protection when replacing and handling all 
electronic parts. 
 
This manual is divided into 4 chapters to facilitate location of technical information. Chapter 1 includes all 
mechanical, fluidic and electronic assemblies are described. Chapter 2 outlines routine maintenance and 
troubleshooting procedures. Chapter 3 includes troubleshooting, including error messages. Finally, 
Chapter 4 includes part identification.  
 

 

Содержание SmartLyte Plus



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды