Diamond SmartLyte Plus Скачать руководство пользователя страница 48

Страница: 48 / 58

1 Introduction

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18 Page 48 of 58

1.5.3. Power Circuits

Power is supplied to this circuit board through connector JP1 from the power supply

assembly. Check points are provided to measure supply voltages. The following list identifies

the check points.

TEST POINT

VOLTAGE

TEST POINT

VOLTAGE

TP1

+24V

TP2

+14V

TP3

+5V

TP4

+3.3V

TP5

2.5V

TP6

-14V

TP7

-2.5V

TP8

+12V

TP9

+2.048V

TP10

4.096V

TP11

+5V

TP12

+2.5V

TP13

NOT USED

TP14

-2.048

TP15

Ion-1

TP16

Ion-2

TP17

Ion-3

TP18

Ion-4

TP19

Ion-5 (NA)

TP20

Ion-6 (NA)

TP21

MFG Only

TP22

MFG Only

TP23

Sample Sensor

TP24

+5V

TP25

Temperature

TP26

+14V

TP27

GND

TP28

GND

TP29

MFG Only

TP30

MFG Only

1.5.4. Microcontroller

The STM32F407 microcontroller, represented as U12, can be located on the CPU board

(slight above & on right of the buzzer). This processor is preloaded with customized software

to control the peripherals – valve, pump, printer, RFID, signal processing, temperature

sensor, sample sensor and buzzer.

1.5.5. EMF and Noise Shielding

SMPS technology used to generate 24V DC supply from 110-220V AC supply. CPU board

has voltage regulator and switches to ±14V, ±2.048, ±5, ±2.5 and 3.3V. These linear

regulators and switches generate EMF noise which may interfere with sample analysis

resulting in inaccurate readings. For high accuracy and precision, the signal processing

amplifier on customized CPU is shield under using conductive metal shield plate. This shield

must be installed and covered for optimal performance.

1.5.6. Fluid Pack Sensor

SmartLyte

Plus uses standard fluids from pack for calibration, sample analysis, and waste

storage. To ensure that the fluid pack is present, an optical reflective sensor is mounted on
the CPU. The photo-detector signal is used to determine presence/absence of fluid pack.

Содержание SmartLyte Plus



























































Результаты поиска

Содержание SmartLyte Plus

Отзывы:

Бренды по названию

Популярные бренды

Diamond SmartLyte Plus, Руководство по обслуживанию

Результаты поиска

Содержание SmartLyte Plus

Отзывы:

Бренды по названию

Популярные бренды