manualshive.com logo in svg

Diamond SmartLyte Plus, Руководство по обслуживанию

Поделиться
Скачать
Diamond SmartLyte Plus Скачать руководство пользователя страница 40

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 40 of 58 

 

1.4. Fluidic Modules 

1.4.1.  Standard A 

Standard A, STD A, is drawn to the electrode module by a  vacuum provided by the peristaltic 

pump. When STD A is to be aspirated into the electrode module, solenoid valve A is opened and 

solenoid valves B, C, V and R are closed.  

STD A is drawn from the Fluid Pack, to the fill port, through the sample probe up to the sample 

sensor. When the sample sensor detects fluid, solenoid valve V is opened and solenoid valve A is 

closed. The peristaltic pump continues to pump STD A into the electrode module. At the trailing 

edge of the STD A is air.  

When  the sample sensor  detects air, the peristaltic pump stops. Standard A should fill the 

electrode module. During the time STD A is aspirated into the electrode module, the reference 

housing is pressurized due to the peristaltic pump providing pressure to the reference solution 

line and solenoid valve R being closed. A small amount of reference solution is forced out through 

the reference junction to provide contact to the sample. 

Once measurement is complete, the peristaltic pump moves the fluid back to the Fluid Pack into 

the Waste Container. 

 

1.4.2.  Standard B and C 

The process for STD B  and STD C is identical to that of STD A  with the exception of the 

operation of solenoid valves B and C. These solenoid valves are operated in reverse order of 

STD A aspiration. 

1.4.3.  Reference Solution 

The reference solution is circulated back into the Reference Solution container in the Fluid Pack. 

The reference housing  has an in and an out port. It  is filled automatically using the second 

winding of the peristaltic pump and solenoid valve R. The reference solution connector allows for 

the reference housing tubing to be plugged into the reference solution circuit. As the peristaltic 

pump aspirates reference solution, solenoid valve R is opened to allow excess solution to be 

pumped into the reference return line of the Fluid Pack. 

1.4.4.  Waste Liquids 

Calibration standards and sample waste are all pumped out of the left side of the electrode tray 

(green-banded tubing) through the peristaltic pump to the waste line and into the waste bag of the 

Fluid Pack. The Waste Container has an internal one-way valve is incorporated to prevent waste 

material from leaking out of the Fluid Pack. 

 

Содержание SmartLyte Plus



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды