Diamond Remote Tomo5 Скачать руководство пользователя страница 24

Страница: 24 / 29

Document Title:
Remote Tomo5 operation guide for eBIC microscopes

Author(s):
Kyle Morris
Julika Radecke
Andrew Howe

Version:
2.0.3
Date:
27 Jun 2022

If you have any questions at any point during set-up, please ask your Local Contact for assistance Page 24 of 29

5 Final checks and data collection

5.1 Auto Functions and alignment

5.1.1 Alignments via Autofunctions

Navigate in the Atlas (refer to 3.1.3) to an area of carbon to perform alignments

You must be at eucentric height (refer to 3.2.2) and the objective aperture should be removed

Use the Auto Functions in the order as below:

The order should be followed, if Auto Function is successful then move on to the next

Ensure that you select the corresponding Preset for each Auto Function alignment

1. Auto Functions

→

Auto-Functions (TEM)

→

Auto-eucentric by stage tilt

→

Start

Presets -> Eucentric Height for Auto-eucentric by stage tilt or beam tilt

2. Auto Functions

→

Auto-Functions (TEM)

→

Autofocus

→

Start

Presets

→

Focus for Autofocus

3. Auto Functions

→

Auto-Functions (TEM)

→

Autostigmate

→

Start

Presets

→

Thon Ring for Autostigmate

4. Auto Functions

→

Auto-Functions (TEM)

→

Autocoma

→

Start

Presets

→

Thon Ring for Autocoma

Содержание Remote Tomo5






























Результаты поиска

Содержание Remote Tomo5

Отзывы:

Похожие инструкции для Remote Tomo5

Бренды по названию

Популярные бренды

Diamond Remote Tomo5, Руководство по эксплуатации

Результаты поиска

Содержание Remote Tomo5

Отзывы:

Похожие инструкции для Remote Tomo5

Бренды по названию

Популярные бренды