manualshive.com logo in svg

DG TOE10G IP, Инструкция к демонстрации

Поделиться
Скачать
DG TOE10G IP Скачать руководство пользователя страница 39

dg_toe10gip_cpu_instruction_xilinx_en.doc

 

 

23-Aug-19 

Page 39 

 

8.4  Receive Data Test (client to server) 

 
To transfer data from client to ser

ver, select ‘3’ to run receive data test on the server FPGA 

and select ‘2’ to run send data test on the client FPGA. User inputs test parameters through 
Serial console. The sequence to run the test is shown as below. 
 

1)  On Serial console of server, input three parameters in receive data test. 

a)  Input transfer size: Unit of transfer size is byte. Valid value is 0x8 - 0x7_FFFF_FFF8. 

The input must be aligned to 8. The input is decimal unit when user inputs only digit 
number. User can add “0x” to be a prefix when the input is hexadecimal unit. 

b)  Input data verifi

cation mode: Set ‘0’ to disable data verification or ‘1’ to enable data 

verification to verify data from FPGA running as client. It 

is recommended to set ‘1’ to 

verify data from client. 

c)  Input Mode: Mode of FPGA to transf

er data. Input ‘1’ to set server mode. 

2) 

If inputs are valid, “Wait Open connection …” will be displayed. 

3)  On Serial console of client, input three test parameters in send data test. 

a)  Input transfer size: Unit of transfer size is byte. Valid value is 0x8 - 0x7_FFFF_FFF8. 

The input must be aligned to 8. The input is decimal unit when user inputs only digit 
number. User can add “0x” to be a prefix when the input is hexadecimal unit. This 
value must be equal to transfer size on server FPGA (input in step 1a). 

b)  Input packet size: Unit of packet size is byte. Valid value is 8 

– 8960. The input must 

be aligned to 8. The input is decimal unit when user inputs only digit number. User can 
add “0x” to be a prefix when the input is hexadecimal unit. 

c)  Input Mode: Mode of FPGA to transfer data. Input 

‘0’ to set client mode. 

If inputs are valid, the operation will start. 

4)  After  running  client,  current  transfer  size  is  displayed  on  both  Serial  consoles  every 

second. 

5) 

“Connection closed” and “Received data completed” are displayed on  Serial console  of 
server after client finishes sending all data and closing the connection. Finally, total transfer 
size and performance are displayed on both Serial consoles. 

Содержание TOE10G IP












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды