background image

1

EC500-SD Installation Guide

Package Contents

DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision 

and details of the installation procedure, please refer to the user's manual.

www.dfi.com

• 

1 EC500-SD system unit

• 

Mounting screws for SATA drive

• 

Mounting screws for Mini PCIe module

Panel

Front View

Rear View

COM 2

Power Button

(1)

Reset Button

USB 2.0

COM 3

Status LED

HDD LED

COM 1

COM 4

Remote power

on/off

DC-in

USB 3.0

DVI-I

(DVI-D Signal)

CFast

LAN 1

LAN 2

VGA

Line-out

HDMI

Microphone

Notes:

1. Please gently press the power button to avoid possible damages.
2. The HDMI is a DP/HDMI combo port but can only provide HDMI connectivity (unless wired as a DP 

port by request). Please plug in an HDMI cable with the right orientation and alignment to avoid 
damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not 
inserted correctly. For detailed instructions, please see a video at https://youtu.be/SUj07rfN5l8.

Align this edge with the 

left side of the connector

Angled-corner

(up)

Angled-corner

Aligning side

(left)

pin

Содержание EC500-SD











Отзывы: