background image

ENGLISH

8

 

  WARNING: 

To reduce unexpected tool 

movement, do not switch the tool on or 
off while under load conditions. Allow 
the grinder to run up to full speed before 
touching the work surface. Lift the tool 
from the surface before turning the tool 
off. 

PADDLE SWITCH (FIG. 1)

The lock-off lever (a), located on the paddle switch, 
is a safety feature that prevents accidental activation 
of the grinder. 

To turn the tool on, push the lock-off lever (a) toward 
the back of the tool, then depress the paddle switch 
(b). The tool will run while the switch is depressed. 
Turn the tool off by releasing the paddle switch.

 

  WARNING: 

Do not disable the lock-off 

lever. If the lock-off lever is disabled, the 
tool may start unexpectedly when it is 
laid down.

OPERATION

Instructions for Use

 

  WARNING: 

Always observe the safety 

instructions and applicable regulations.

Install Grinding Wheels (fi g. 2)

  1. Hold the spindle (c) using the spanner provided.

  2. Loosen the collet nut (e) by turning it 

counterclockwise.

  3. Insert the shank of the accessory into the collet 

(d).

  4. Securely tighten the collet using the spanner 

provided.

To remove the accessory, proceed in reverse order.

 

   

WARNING:

 Grasp tool firmly with both 

hands to maintain control of the tool at 
start up and during use and until the 
wheel or accessory stops rotating. Make 
sure the wheel has come to a complete 
stop be fore laying the tool down.

Put the work in a vise or clamp it securely. Use a 
face mask over the nose and mouth if the operation 
raises dust. Treat the wheel with respect. Do not 
jam the wheel into the work or use unnecessary 
pressure. Grind only on the face of the wheel unless 
you have a special wheel specifically make to permit 
grinding on the side of the wheel.

Proper Hand Position (fi g. 3)

 

  

WARNING: 

To reduce the risk of 

serious personal injury, 

ALWAYS

 use 

proper hand position as shown. 

 

  

WARNING:

 To reduce the risk of 

serious personal injury, 

ALWAYS

 hold 

securely in anticipation of a sudden 
reaction. 

Proper hand position requires one hand on the body, 
with the other hand on the neck of the die grinder, 
as shown in figure 3. 

MAINTENANCE

Your D

E

WALT power tool has been designed to 

operate over a long period of time with a minimum 
of maintenance. Continuous satisfactory operation 
depends upon proper tool care and regular cleaning.

 

  

WARNING: To reduce the risk of 
injury, turn unit off and disconnect 
machine from power source

 before 

installing and removing accessories, 
before adjusting or changing set-ups 
or when making repairs. Be sure 
the switch is in the OFF position. An 
accidental start-up can cause injury.

Motor Brushes

Keep brushes clean and sliding freely in their guides. 
Carbon brushes have varying symbols stamped 
into them, and if the brush is worn down to the line 
closest to the spring, they must be replaced. New 
brush assemblies are available at your local service 
center.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

 

  

WARNING:

 Blow dirt and dust out of 

the main housing with dry air as often as 
dirt is seen collecting in and around the 
air vents. Wear approved eye protection 
and approved dust mask when 
performing this procedure. 

Содержание DW887N

































Отзывы: