DeWalt DW677, Оригинальное руководство пользователя

Страница: 18 / 72

16
EngLIsh
Intended Use
Your planer has been designed for professional planing
of wood.
DO nOt
use under wet conditions or in the presence of
flammable liquids or gases.
These planers are professional power tools.
DO nOt
let children
come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Adjusting the Depth of Cut (Fig. C)
Turn the planing depth adjustment knob 4 to the required
depth of cut.
One graduation corresponds to a depth of cut of 0.1 mm.
Attaching and Removing the Parallel Fence
(Fig. A, B, D)
The parallel fence 13 is used for optimum tool control on
narrow workpieces.
1. Slacken the wing bolt 6 .
2. Fit the parallel fence
13
in the hole
7
from either side.
3. Tighten the wing bolt.
4. To remove the parallel fence, proceed in reverse order.
Removing Reversible Cutters (Fig. E)
1. Loosen the three bolts 14 with the spanner 15 supplied.
2. Flap the side guard
8
up.
3. Slide the cutter 16 out of its holder.
4. Reverse the cutter or replace it.
WARNING: Always replace both cutters.
5. Slide the cutter into the holder. Make sure that the cutter is
flush with the planing shoe 17 .
6. Tighten the three bolts 14 .
Prior to Operation:
Adjust the depth of cut.
If necessary, fit and adjust the parallel fence.
WARNING: Use sharp cutters only.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
12
, with the other hand on the front handle
4
.
Switching On and Off (Fig. A, B)
Your planer is equipped with a safety switch to prevent
inadvertent operation.
1. Switching on: press the lock-off button 2 and subsequently
press the on/off switch 1 .
2. Release the lock-off button 2 .
3. Switching off: release the on/off switch 1 .
Always switch off the tool when work is finished and
before unplugging.
Planing (Fig. A, B)
1. Switch the tool on as described.
2. Slowly move the planer over the workpiece.
WARNING: The feed speed should not be too high,
especially when using the maximum depth of cut and
planing width.
nOtE: Remember that several shallow cuts are better than one
deep cut.
3. Switch the tool off.
Your planer is equipped with a parking shoe
11
. After switching
off the tool can be put down without waiting for the cutters to
come to a standstill.
Dust Extraction
Whenever possible, connect a dust extraction device designed
in accordance with the relevant regulations regarding
dust emission.
MAINTENANCE
Your D
e
WALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.