background image

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and 
receiver.
—Connect the equipment into an outlet on a circuit 
different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV 
technician for help.

Caution—use of controls or adjustments or performance 
of procedures other than those specified herein may 
result in hazardous radiation exposure.

Caution: 
This device complies with Part 15 of the FCC Rules / 
Industry Canada licence-exempt RSS standard(s). 
Operation is subject to the following two conditions: (1) 
this device may not cause harmful interference, and (2) 
this device must accept any interference received, 
including interference that may cause undesired 
operation. 

Le présent appareil est conforme aux CNR d'Industrie 
Canada applicables aux appareils radio exempts de 
licence. L'exploitation est autorisée aux deux conditions 
suivantes : (1) l'appareil ne doit pas produire de 
brouillage, et (2) l'utilisateur de l'appareil doit accepter 
tout brouillage radioélectrique subi, même si le 
brouillage est susceptible d'en compromettre le 
fonctionnement.

Changes or modifications not expressly approved by the 
party responsible for compliance could void the user's 
authority to operate the equipment.

This equipment has been tested and found to comply 
with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference in a residential installation. This equipment 
generates uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that 
interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio 
or television reception, which can be determined by 
turning the equipment off and on, the user is 
encouraged to try to correct the interference to radio 
communications. However, there is no guarantee that 
interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio 
or television reception, which can be determined by 
turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or 
more of the following measures:

11

Содержание DW0330S














Отзывы: