background image

3

Electrical Safety

The electric motor has been designed for one voltage range only. Always check that 

the power supply corresponds to the voltage on the rating plate. 220–240 V AC 

means your tool will operate on alternating current. Operation at a voltage outside this 

range can cause loss of power and can result in overheating. All D

E

WALT tools are 

factory tested; if this tool does not operate, check the power supply. Your D

E

WALT 

tool is double insulated, therefore no earth wire is required.
 • 

Young children and the infirm.

 This appliance is not intended for use by young 

children or infirm persons without supervision. 

    –  This appliance is not intended for use by persons (including children) with 

reduced physical, sensory or mental capabilities, or lack of experience and 

knowledge, unless they have been given supervision or instruction concerning 

use of the appliance by a person responsible for their safety.

    –  Children should be supervised to ensure that they do not play with the appliance.
  •

  Replacement of the supply cord. 

If the supply cord or plug is damaged, it must 

be replaced by the manufacturer or an authorised D

E

WALT Service Centre in 

order to avoid a hazard.

Extension Cords

CAUTION: 

Use only extension cords that are approved by the country’s Electrical 

Authority. Before using extension cords, inspect them for loose or exposed wires, 

damaged insulation and defective fittings. Replace the cord if necessary.

Specific Safety Rules for Worklights

WARNING:

 Fire hazard. Do not operate worklight near flammable liquids or in 

gaseous or explosive atmospheres. Internal sparks may ignite fumes causing personal 

injury.
  •  Do not expose light to wet or damp areas. Do not expose light to rain or snow. 
  •  Do not wash light with water or allow water to get inside light. Do not submerge 

light in water at any time.

WARNING: DO NOT PLACE THE WORKLIGHT IN A POSITION WHICH MAY CAUSE 

ANYONE TO 

intentionally or unintentionally stare into the light. Serious eye injury 

could result.

CAUTION: When not in use, place light on its side on a stable surface where it 

will not cause a tripping or falling hazard. 

Some products with large battery packs 

will stand upright on the battery pack but may be easily knocked over. 

WARNING: 

We recommend the use of a residual current device with a residual 

current rating of 30mA or less.
  •  The label on your light may include the following symbols. The symbols and their 

definitions are as follows:

V ................. volts 

A ...............amperes

Hz ............... hertz 

W ..............watts

min ............. minutes 

 ...........alternating current

 ........ direct current 

 ...........alternating or direct current

 .............. Class I Construction 

no ..............no  load  speed

 ...................

 ...................

(grounded) n 

................rated 

speed

 .............. Class  II  Construction 

 .............earthing  terminal

 ...................

(double insulated)  

..............safety alert symbol

…/min ........ per minute  

BPM ..........beats per minute

IPM ............. impacts per minute  

RPM ..........revolutions per minute

SPM ............ strokes per minute  

sfpm ..........surface feet per minute

SAVE ALL WARNINGS AND INSTRUCTIONS FOR 

FUTURE REFERENCE

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include the catalog number and 

voltage. Consult the chart at the end of this manual for compatibility of chargers and 

battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack 

and charger, read the safety instructions below and then follow charging procedures 

outlined.

READ ALL INSTRUCTIONS

  •  Do not charge or use the battery pack in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust. Inserting or removing the battery 

pack from the charger may ignite the dust or fumes.

Содержание DCL030-XE













Отзывы: