13
e n g l i s h
OPERATIOn
Instructions for use
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up can
cause injury.
WARNING:
• Always observe the safety instructions and
applicable regulations.
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approx.
5 kg). Excessive force does not speed up drilling
but decreases tool performance and may shorten
tool life.
• Do not drill or drive too deep to prevent damage
to the dust cover.
• Always hold the tool firmly with both hands and
ensure a secure stance.
• Always operate the tool with the side handle
properly mounted.
• If the cutting tool is no longer sharp, replace with
a new cutting tool.
Prior to Operation:
• Make sure your battery pack is (fully) charged.
• Make sure the battery pack is properly seated.
Proper Hand Position (fig. A, I)
WARNING:
To reduce the risk of serious
personal injury,
AlWAyS
use proper
hand position as shown.
WARNING:
To reduce the risk of serious
personal injury,
AlWAyS
hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the
side handle (9), with the other hand on the main
handle (10).
Switching On and Off (fig. A)
• To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
• To stop the tool, release the switch.
• To lock the tool in off position, move the forward/
reverse slider (2) to the central position.
Hammerdrilling (fig. A)
• Set the mode selector switch (3) to the
"hammerdrilling" position.
• Insert the appropriate drill bit. For best results use
high quality carbide-tipped bits.
• Adjust the side handle (9) as required.
• If necessary, set the drilling depth.
• Mark the spot where the hole is to be drilled.
• Place the drill bit on the spot and switch on the
tool.
Rotary Drilling (fig. A, H)
• Set the mode selector switch (3) to the "rotary
drilling" position.
• Depending on your tool, follow either of the
following instructions:
- Fit a chuck adaptor/chuck assembly (DCH363).
Keyed and keyless chucks and chuck adaptors
can be purchased separately. Special SDS
Plus
®
adaptors with threaded sections are
available for use with standard 10 or 13 mm
chucks to enable straight shank bits to be
used.
- Replace the SDS Plus
®
tool holder with the
keyless chuck (16) (DCH364).
• Proceed as described for hammerdrilling.
CAUTION:
Never use the keyless chuck
(16) in the hammerdrilling mode. Only the
SDS Plus
®
toolholder should be used for
hammerdrilling.
Screwdriving (fig. A, H)
• Set the mode selector switch (3) to the "rotary
drilling" position.
• Select the direction of rotation.
• Depending on your tool, follow either of the
following instructions:
- Insert a special SDS Plus
®
screwdriving adaptor
for use with hexagonal screwdriver bits which
can be purchased separately (DCH363).
- Replace the SDS Plus
®
tool holder (5) with the
keyless chuck (16) (DCH364).
• Insert the appropriate screwdriver bit. When
driving slotted head screws, always use bits with
a finder sleeve.
• Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
Содержание DCH363
