12
e n g l i s h
• Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. f)
• Insert the required drill bit.
• Slacken the side handle (9).
• Fit the depth adjustment rod (8) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
forward/Reverse Slider (fig. G)
• Push the forward/reverse slider (2) to the LH-side
for forward (RH) rotation. See arrows on tool.
• Push the forward/reverse slider (2) to the RH-side
for reverse (LH) rotation.
CAUTION:
Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
Replacing the SDS Plus
®
Tool Holder
with the keyless Chuck (fig. H)
DCH364
• Turn the locking collar (6) into the unlocked
position and pull the SDS Plus
®
tool holder (5) off.
• Push the keyless chuck (16) onto the spindle and
turn the locking collar into the locked position.
• To replace the keyless chuck with the SDS Plus
®
tool holder, first remove the keyless chuck the
same way as the SDS Plus
®
tool holder was
removed. Then place the SDS Plus
®
tool holder
the same way as the keyless chuck was placed.
CAUTION:
Never use the keyless chuck
(16) in the hammerdrilling mode. Only the
SDS Plus
®
toolholder should be used for
hammerdrilling.
Replacing the Dust Cover (fig. D)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
• Pull back the SDS Plus
®
tool holder locking
sleeve (15) and pull the dust cover (7) off.
• Fit the new dust cover.
• Release the SDS Plus
®
tool holder locking sleeve.
Selecting the Operating Mode (fig. C)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling
Hammering only: for light chipping
• To select the operating mode, press the safety
lock (4) and rotate the mode selector switch (3)
until it points to the symbol of the required mode.
• Release the safety lock and check that the mode
selector switch is locked in place.
WARNING:
Do not select the operating
mode when the tool is running.
Inserting and Removing SDS Plus
®
Accessories (fig. D)
Your rotary hammerdrill uses SDS Plus
®
accessories
(refer to the inset in fig. D for a cross-section of an
SDS Plus
®
bit shank).
• Clean and grease the SDS Plus
®
bit shank.
• Insert the SDS Plus
®
bit shank into the SDS Plus
®
tool holder (5).
• Push the bit down and turn it slightly until it fits
into the slots.
• Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the SDS Plus
®
tool holder.
• To remove a bit, pull back the SDS Plus
®
tool
holder locking sleeve (15) and pull out the bit.
fitting the Side Handle (fig. E)
The side handle (9) can be fitted to suit both
right-hand and left-hand users.
WARNING:
Do not use the tool without
the side handle properly assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
• For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
Содержание DCH363
