DeWalt DC927-XE Скачать руководство пользователя страница 7

5

b.  and the battery liquid gets into your eyes, flush them with clean water for a 

minimum of 10 minutes and seek immediate medical attention. (

Medical note:

 

The liquid is 25-35% solution of potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION)

 

•  Do not incinerate the battery pack even if it is severely damaged or is 

completely worn out. 

The battery pack can explode in a fire. Toxic fumes and 

materials are created when lithium ion battery packs are burned.

 

•  If battery contents come into contact with the skin, immediately wash area 

with mild soap and water.

 

If battery liquid gets into the eye, rinse water over the 

open eye for 15 minutes or until irritation ceases. If medical attention is needed, 

the battery electrolyte is composed of a mixture of liquid organic carbonates and 

lithium salts.

 • 

Contents of opened battery cells may cause respiratory irritation.

 

Provide fresh 

air. If symptoms persists, seek medical attention.

WARNING:

 Burn hazard. Battery liquid may be flammable if exposed to spark or 

flame. 

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the

 

nickel cadmium, nickel metal hydride or lithium ion batteries (or 

battery packs) indicate that the costs to recycle these batteries (or 

battery packs) at the end of their useful life have already been paid 

by D

E

WALT. In some areas, it is illegal to place spent nickel 

cadmium, nickel metal hydride or lithium ion batteries in the trash 

or municipal solid waste stream and the RBRC program provides an environmentally 

conscious alternative.
RBRC™ in cooperation with D

E

WALT and other battery users, has established 

programs in the United States and Canada to facilitate the collection of spent nickel 

cadmium, nickel metal hydride or lithium ion batteries. Help protect our environment 

and conserve natural resources by returning the spent nickel cadmium and nickel 

cadmium, nickel metal hydride or lithium ion batteries to an authorized D

E

WALT 

service center or to your local retailer for recycling. You may also contact your local 

recycling center for information on where to drop off the spent battery.
RBRC™ is a registered trademark of the 

Rechargeable Battery Recycling Corporation.

Important Safety Instructions for all Battery Chargers

SAVE THESE INSTRUCTIONS: 

This manual contains important safety and operating 

instruc tions for battery chargers.
  •  Before using charger, read all instructions and cautionary markings on charger, 

battery pack, and product using battery pack.

DANGER: 

Electrocution hazard. 240 volts are present at charging terminals. Do not 

probe with conductive objects. Electric shock or electrocution may result.

WARNING: 

Shock hazard. Do not allow any liquid to get inside charger. Electric shock 

may result.

CAUTION:

 

Burn hazard. To reduce the risk of injury, charge only D

E

WALT 

rechargeable batteries. Other types of batteries may burst causing personal injury and 

damage.

CAUTION: 

Under certain conditions, with the charger plugged in to the power 

supply, the exposed charging contacts inside the charger can be shorted by foreign 

material. Foreign materials of a conductive nature such as, but not limited to, steel 

wool, aluminum foil, or any buildup of metallic particles should be kept away from 

charger cavities. Always unplug the charger from the power supply when there is no 

battery pack in the cavity. Unplug charger before attempting to clean.
 

•  DO NOT attempt to charge the battery pack with any chargers other than the 

ones in this manual.

 The charger and battery pack are specifically designed to 

work together. 

  •  These chargers are not intended for any uses other than charging D

E

WALT 

rechargeable batteries

. Any other uses may result in risk of fire, electric shock 

or electrocution.

  •  Do not expose charger to rain or snow.

 

•  Pull by plug rather than cord when disconnecting charger.

 This will reduce risk 

of damage to electric plug and cord.

  •  Make sure that cord is located so that it will not be stepped on, tripped over, 

or otherwise subjected to damage or stress.

 

•  Do not use an extension cord unless it is absolutely necessary.

 Use 

of improper extension cord could result in risk of fire, electric shock, or 

electrocution.

Содержание DC927-XE

















Отзывы: