Ver. 02/2009
Type / Format
Scanning Element
Image Picture Element
Effective Picture Element
Resolution (TV lines)
Minimum Illumination
S/N Ratio
Back Light Compensation
Exposure Control
Sync System
Gamma Compensation
Video Output
White Balance
Auto White Balance Range
Power Range*
Power Consumption
Operating Temperature
Storage Temperature
General Specification
F1.6
F1.6~F2.4
Minimum Object Distance
50cm
Field Of View
Diagonal
92.8º~39.4º
Horizontal
71.0º~31.6º
Vertical
51.6º~23.6º
Lens Specification
Contents:
• ¾” Rubber Grommet
• Screw Pack
• Torx Driver
• Quick Installation Adaptor (optional)
NTSC
2:1 Interlace,
H15.750KHz / V :50Hz
752(H) x 582(V)
540
50dB
Central Area for DC IRIS Lens
DC Auto IRIS Drive
INT
0.45
1.0Vpp, 75
Ө
Unbalanced
2700K – 11000K
4.2W (Max)
-20°C ~ +60°C
0.65 Lux @ F1.2
Automatic White Balance
752(H) x 582(V)
DC 12V -10% ± 15%
1/3” Interline CCD
Central Area for Auto IRIS Lens
DC Auto IRIS Drive
1.0Vpp, 75 ohm Unbalanced
4.2W (Max)
2700K – 11000K
Automatic White Balance
0.45
INT
50dB
0.65 Lux @ F1.2
540
1/3” Interline CCD
2:1 Interlace,
H15.625KHz / V :50Hz
PAL
-20°C ~ +60°C
3.0~9.0mm
F1.2
F1.2~F360
50cm
116.2º~39.7º
90.0º~31.8º
66.2º~23.9º
NC
NC
NC
FL
BLC
AGC
------
------
------
OFF
OFF
EX
------
------
------
ON
ON
NORMAL
OFF
N
O
N
O
I
T
C
N
U
F
1
2
3
4
5
6
A1
A2
Camera Adjustments
A1 : Focus Adjuster
A2 : Field of View Adjuster
A3 : *AI Level Adjustment
A4 : Service Jack
A5 : Function Control
Dip Switches
*AI Level Adjustment is factory set.
Should not normally require adjustment
*There is a Service Jack supplied for camera adjustment.
A5
A4
A3
9.0~22.0mm
F1.8
F1.8~F360
0.2m
39.0º~17.6º
30.7º~14.1º
22.7º~10.6º
DIP Switches
The bank of DIP switches allows the following settings to be made:
Flickerless Mode (FL/ON)
:
The camera reduces flicker in the image under
fluorescent lighting.
Back Light Compensation (BLC)
When set ON, this option improves the
camera’s response to strong, unwanted lighting
effects behind the required subject.
Low Light Sensitivity
(AGC-EX/AGC-NORMAL)
When set to EX, sensitivity in low light will
automatically increased.
Select “NORMAL” will remove noise from the image,
but it will also limit the camera’s sensitivity.
Vertical Phase Adjustment (V-Phase)
Use this adjustment when using an AC supply to align the camera phase with that
of the supply.
DC-IRIS Adjustment (ALC)
This is factory preset. It should not normally require adjustment.
Tamper Proof Internal Dome Camera
Instruction Manual
RoHS
ɀ
US Patent Pending
Regulatory Compliance
Emissions
FCC part 15 Class B
CE:
EN55011
ICES-003
EN55022
CISPR
11
CISPR22
ANSI
C63.4
Immunity
CE:
EN50130-4
RoHS
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against armful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required
to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifications not expressly approved by seller.
The party responsible for FCC compliance could void the user’s authority to operate the equipment and could create a hazardous
condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Template
Cable access
When the cables are threaded through the mounting surface,
create an apture indicated “
T2
”. It can be simply threaded for
use with the quick install adapter .
When mounting the dome on a surfce with the four
T1
screws,
use one of the side knock-outs as indicated for cable entry
(see Installation Guide overleaf ).
Surface mount (In a wall or ceiling)
Using Quick Install Adaptor:
Create an aperture in the mounting surface to a diameter of
1.5” (38mm) as indicated by “
T2
”.
The aperture is also avaliable for cable access (3/4”, 19mm).
Using screws:
Create four holes at template positions ‘
T1
’, use the screws
and plugs provided in the screw kit where the mounting
surface is appropriate.
T1
T2
Side Knock-out
Side Knock-out
Side Knock-out
Side Knock-out
Cable Access
T1
T1
T1
125.7º~29.9º
3.3~12mm
F1.4
F1.4~F360
89.8º~23.9º
63.6º~17.9º
50cm
V531-DF003-001
4-9mm
2.9-10mm
F1.2
F1.2~F360
0.15m
125.0º~36.0º
94.6º~28.8º
68.4º~21.6º
2.5~6.0mm
F1.2
F1.2~F360
0.5m
145.5º~59.1º
111.6º~47.3º
82.2º~35.5º
Focal Length
F-No.
Iris Range
-10°C ~ +50°C
-10°C ~ +50°C
DC 12V -10% ± 15%