Develco ZHOT101 Скачать руководство пользователя страница 15

Страница: 15 / 20

General network behaviour

6.1

Installation

When the device is virgin and powered for the first time it will start looking for a ZigBee PAN

Coordinator or router to join. The device will scan each ZigBee channel starting from 11 to 24. The

LED will flash once every second until it joins a device.

#Scan mode - 1

Scan all 16

ZigBee channel

until join network

or 15 minutes

#Sleep mode

MCU is in sleep

mode (Radio off)

15 minutes

#Scan mode - 2

Scan all 16

ZigBee ch x 4 or

until join network

~ 2 minutes

#Sleep mode

MCU is in sleep

mode (Radio off)

15 minutes

#Scan mode - 2

Scan all 16

ZigBee ch x 4 or

until join network

~ 2 minutes

The device will start up using scan mode 1. To increase battery lifetime when the device is joining a

network for the first time a scan mode 2 will be used after scan mode 1 has expired. Scan mode 1 it

will only be executed one time when the devise is powered.

In section 5 “MMI” it is explained how to put the device into a join or leave network mode.

Network settings are stored in NV-memory are after a power cycle the device re-join the same

network.

If the device has to join a new PAN coordinator the MMI menu supports a “Reset To Factory Fresh

Settings” mode. This will erase all current network information.

6.2

Normal – Keep alive

The device is sending a “keep alive” message to the PAN coordinator every 15 minute to verify that

the device is still connected to the network.

6.2.1

Network lost

If no “keep alive” responses are received 5 times in a row (Worst case 1h15m), the devices will start

scanning every ZigBee channel for the PAN coordinator and try to re-join it. After scanning all 16

channels 4 times in a row the device will enter sleep mode. The device will toggle between each mode

until a re-join occur.

When the device is in scan mode the LED will flash once every second until it re-joins the network.

According to the ZigBee specification TX is NOT allowed to be enabled all the time and a TX silent

period has to be defined.

#Scan Mode

Scan all 16 ZigBee channel x 4

~ 2 minutes

LED is flashing once every 1 sec

#Sleep mode

MCU is in sleep mode (Radio off)

15 minutes

LED = OFF

Содержание ZHOT101





















Результаты поиска

Содержание ZHOT101

Отзывы:

Похожие инструкции для ZHOT101

Бренды по названию

Популярные бренды

Develco ZHOT101, Техническое руководство

Результаты поиска

Содержание ZHOT101

Отзывы:

Похожие инструкции для ZHOT101

Бренды по названию

Популярные бренды