Devantech ESP32LR20 Скачать руководство пользователя страница 5

Страница: 5 / 15

ESP32LR20

User Manual v1.02

RB ReBoot.

This will restart the module. It may produce a lot of random characters as the

ESP32’s boot logging runs at a different baud rate. If it succeeds in connecting to your
network it will report the IP address.

Re-Booting.. .

崳

⸮⸮⸮⸮⸮⸮⸮⸮

#XL###C

5)5)

ia b

⸮⸮⸮⸮⸮

⸮⸮⸮ ⸮ ⸮⸮⸮⸮⸮⸮⸮⸮

奅

UY o

##i#U 5

⸮⸮*⸮⸮

⸮ ⸮⸮⸮⸮⸮

⸮

⸮ ⸮⸮⸮⸮⸮

WiFi connected.
IP address:

192.168.0.6

Sets the modules IP address.

Enter IP followed by the required IP address. Entering address 0.0.0.0 means the IP will be

obtained from your networks DHCP server. The new IP address will take effect after the
next re-boot.

IP “192.168.0.123”

OK. Saved IP Address: 192.168.0.123

SB Sets the SuBnet mask.

SB “255.255.255.0”
OK. Saved Subnet Mask: 255.255.255.0

GW Sets the GateWay address.

This is normally the IP address of your router.

GW “192.168.0.1”

OK. Saved Gateway Address: 192.168.0.1

Devantech Ltd.

www.robot-electronics.co.uk

Содержание ESP32LR20












Результаты поиска

Содержание ESP32LR20

Отзывы:

Devantech ESP32LR20, Руководство пользователя, Страница: 5 / 15

Результаты поиска

Содержание ESP32LR20

Отзывы: