manualshive.com logo in svg

Dettson COND-ELD-09, Инструкция по установке и руководство пользователя

Поделиться
Скачать
Dettson COND-ELD-09 Скачать руководство пользователя страница 1

INSTALLATION INSTRUCTIONS AND

HOMEOWNER’S MANUAL

Models:
COND-ELD-09
COND-ELD-12
COND-ELD-18
COND-ELD-24
COND-ELD-CO-09
COND-ELD-CO-12
COND-ELD-CO-18
COND-ELD-CO-24

INSTALLER / SERVICE TECHNICIAN:

Use the information in this manual for the installation / servicing and keep the document near the furnace
for future reference.

Communication wire connected between the indoor and outdoor units must be rated for at least 120VAC,
they are protected by the outdoor unit breaker and must be sized appropriatly.

Do not install any metering device on the indoor coil. The expension valve is located in the outdoor unit.
If a metering device is already installed in the indoor coil, it must be removed.

Both refrigerant lines must be separately insulated in order to avoid condensation and to ensure proper
efficiency.

COND-ELD

-09

-12

-18

-24

Liquid line dia (In)

1/4

1/4

1/4

1/4

Gas line dia (In)

3/8

3/8

1/2

5/8

HOMEOWNER:

Please keep this manual near the furnace for future reference.

CAUTION:

Do not tamper with the unit or its controls. Call a qualified service technician.

Manufactured by:

Dettson Industries Inc.

Sherbrooke, Qc, Canada

www.dettson.com

Printed in Canada on

2020-05-08

X40258 Rev.A

100% recycled paper

Содержание COND-ELD-09
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды