Detroit Diesel 60 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 172

background image

SERIES 60 ENGINE OPERATOR'S GUIDE

Their use does not permit extension of
recommended oil drain intervals.

The Use of Supplemental
Additives

Lubricants meeting the Detroit
Diesel specifications outlined in this
publication already contain a balanced
additive treatment. Supplemental
additives are generally not necessary
and can even be harmful. These
additives may be marketed as either
oil treatments or engine treatments and
are discouraged from use in Detroit
Diesel engines.

Engine damage resulting from the
use of such materials is not covered
by your Detroit Diesel Corporation
warranty. Detroit Diesel will not
provide statements beyond this
publication relative to their use.

When to Change Oil

The length of time an engine may
operate before an oil change depends
upon the lubricant and fuel used,
engine oil consumption, and the
operating cycle.

USED ENGINE OIL

To avoid injury to skin from
contact with the contaminants in
used engine oil, wear protective
gloves and apron.

The maximum interval at which
the engine may operate before the
oil and filters must be changed is
listed in Table 20. Oil analysis may be
used to determine whether this interval
should be shortened, but it should not
be used to lengthen the interval.

Engine Application

Drain Interval

Highway Truck & Motor Coach

15,000 Miles (24,000 km)

City Transit Coach#

6,000 Miles (9,600 km)

Fire Truck or Crash/Rescue Vehicle

6,000 Miles (9,600 km), 300 Hours or
1 Year, whichever comes first

Construction, Industrial or Agriculture

250 Hours or 1 Year, whichever comes
first

Stationary Generator, Prime Power or
Continuous

300 Hours or 3 Months, whichever
comes first

Stationary Generator, Standby

150 Hours or 1 Year, whichever comes
first

Table 20

Maximum Oil Drain and Filter Change Interval (Fuel Sulfur
0.05 Weight Percent or Less)

All information subject to change without notice. (Rev. 01/04)

83

6SE484

0401

Copyright © 2004 DETROIT DIESEL CORPORATION

«
...
95
96
97
98
99
...
»

Содержание 60













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 60

Бренд: Jabiru Страницы: 103

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

Бренд: Club Car Страницы: 280

90000 I/C 525 Series

Бренд: Briggs & Stratton Страницы: 16

Бренд: Briggs & Stratton Страницы: 4

Confidant ZT710

Бренд: Kohler Страницы: 24

Бренд: FPT Страницы: 49

Бренд: Lycoming Страницы: 74

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 8

RolloTube Basis

Бренд: RADEMACHER Страницы: 60

Бренд: RADEMACHER Страницы: 64

Бренд: YS Страницы: 2

Бренд: Detroit Diesel Страницы: 6

Бренд: Kingfisher Страницы: 10

Бренд: Honda Страницы: 86

Бренд: LONCIN Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды