Detroit Diesel 60 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 172

background image

SERIES 60 ENGINE OPERATOR'S GUIDE

ENGINE STORAGE

When an engine is to be stored or
removed from operation for a period
of time, special precautions should
be taken to protect the interior and
exterior of the engine, transmission
and other parts from rust accumulation
and corrosion. The parts requiring
attention and the recommended
preparations are given below.

Preparing Engine for
Storage

It will be necessary to remove all
rust or corrosion completely from
any exposed part before applying rust
preventive compound. Therefore,
it is recommended that the engine
be processed for storage as soon as
possible after removal from operation.

The engine should be stored in
a building that is dry and can be
heated during the winter months.
Moisture-absorbing chemicals are
available commercially for use when
excessive dampness prevails in the
storage area.

Temporary Storage (30 Days or
Less)

To protect the engine for a temporary
period of time (30 days or less), follow
this procedure:

1. With the engine at ambient

temperature and cool to the touch,
drain engine crankcase oil into a
suitable container. Dispose of the
oil in an environmentally friendly
manner, according to state and/or
federal (EPA) recommendations.

2. Fill the crankcase to the proper

level with the recommended
viscosity and grade of oil.

3. Fill the fuel tank with the

recommended grade of fuel oil.
Operate the engine for two (2)
minutes at 1200 rpm and no load.
Do not drain the fuel system or
the crankcase after this run.

4. Check the air cleaner and service

it, if necessary.

5. If freezing weather is expected

during the storage period, check
the antifreeze/coolant for required
freeze and inhibitor protection.
Add antifreeze solution to the
cooling system in accordance
with DDC's recommendations.

All information subject to change without notice. (Rev. 01/04)

117

6SE484

0401

Copyright © 2004 DETROIT DIESEL CORPORATION

«
...
129
130
131
132
133
...
»

Содержание 60













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 60

Бренд: E-Z-GO Страницы: 112

Бренд: Sole Diesel Страницы: 40

Бренд: nord Страницы: 91

HYDRO-FORCE 65043

Бренд: Bestway Страницы: 8

Бренд: Raider Страницы: 28

Бренд: YS Страницы: 2

Бренд: Elite Страницы: 2

Бренд: RIEJU Страницы: 63

Бренд: Yanmar Страницы: 222

Бренд: LONCIN Страницы: 64

Бренд: Farymann Diesel Страницы: 137

Бренд: Ingersoll-Rand Страницы: 97

Бренд: Cors-Air Страницы: 21

Бренд: Yanmar Страницы: 6

Бренд: Marine Power Страницы: 56

Бренд: komodo Страницы: 11

Бренд: Yale Страницы: 38

Бренд: Neodrives Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды